參數資料
型號： 4114R-1-104
元件分類： 復位半導體
英文描述： 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit
中文描述： WIDERSTAND NETZWERK DICKFILM 10萬5ST
文件頁數： 58/62頁
文件大?。?/td> 1883K
代理商： 4114R-1-104
Specifications are subject to change without notice.
337
These are the common
methods, materials and
maximum temperature/
time parameters for
soldering and cleaning
processes:
Soldering/Cleaning Methods
REFLOW
FLOW
Hot Air,
Infrared
Vapor Phase
Wave
Process Step
(Solvent)
(Aqueous)
Material
1.
Solder Paste Printing
X
RMA
2.
Adhesive Application
X
Epoxy
3.
Switch Placement
X
4.
Adhesive Cure
X
5. Flux Application
X
Rosin
5. Flux Application
X
Organic Acid
6. Solder (Reflow)
X
63/37 Sn/Pb
7. Solder (Flow)
X
63/37 Sn/Pb
8. Wash (Solvent)
X
ODS Free
9. Wash (Aqueous)
X
DI H2O; Detergent
High Pressure Fluids
X
Ultrasonics
X
Max. Temp.(°C)/Time (Seconds)
240/30
215/180
260/5
6
Solder
Reflow; Convection,
IR and Vapor Phase
GENERAL
Preheat sufficiently using both time
and temp. to bring the flux to activa-
tion and minimize thermal shock.
Consult your solder paste supplier for
the recommended profile.
RECOMMENDED
Typical IR/Convection profile.
Use convection or Vapor Phase when
possible and minimize the time above
reflow temperature.
CAUTION
Do not exceed time and temperature
reflow profile of 240°C for 30 sec. for
Hot Air/IR reflow and 215°C for 3
minutes for vapor phase reflow.
Minimize thermal shock by limiting
temperature ramps to 3°C/sec. and by
stabilizing board and component tem-
perature during preheating.
7
Solder
Flow (Wave)
GENERAL
For maximum component reliability
and performance, minimize the time
of temp. exposure above 200°C.
RECOMMENDED
Typical alloy is Sn63/Pb37. A typical
wave solder zone profile is 245C for
5 sec.
CAUTION
Always preheat before the soldier
wave using the temperature for flux
activation recommended by the man-
ufacturer.
Do not exceed 240C peak tempera-
ture for dual wave solder process
with a flow zone totaling 5 seconds.
Minimize thermal shock by limiting
temperature ramps to 3C/sec. and by
stabilizing board and component
temperature during preheating.
8
Wash
Solvent
GENERAL
Use solvent cleaning primarily
for nonpolar contaminants
such as rosin based flux
residues.
RECOMMENDED
Use any suitable washing sol-
vents that meet ODS require-
ments.
CAUTION
Limit excessive direct spray
pressure to 60 psi.
Allow the assembly to suffi-
ciently cool prior to the wash-
ing operation for minimized
thermal stress.
9
Wash
Aqueous
GENERAL
Use aqueous cleaning primarily
for polar contaminants such as
organic flux residues.
RECOMMENDED
Use De-ionized or Reverse
Osmosis water with multistage
rinsing. Post bake at 100C for
30 minutes to remove any resid-
ual moisture.
CAUTION
Limit excessive direct spray
pressure to 60 psi.
Allow the assembly to sufficient-
ly cool prior to the washing oper-
ation for minimized thermal
stress.
Board Rework Technique
GENERAL
Excessive and/or repeated high
temperature exposure may
affect the component perfor-
mance and reliability.
RECOMMENDED
Hot air reflow technique is pre-
ferred. Use No Clean or Rosin
based fluxes only, OA fluxes are
recommended.
CAUTION
Avoid the use of wave soldering
or soldering irons as a rework
technique. Avoid repeated and
excessive temperature exposure.
PRE-HEATING
(in air)
SOLDERING GRADUAL COOLING
(in air)
200°C
100°C
0°C
ONE MINUTE
MIN.
20 SECOND
MAX.
230°C
PRE-HEATING
(in air)
SOLDERING GRADUAL COOLING
(in air)
200°C
100°C
0°C
ONE MINUTE
MIN.
5 SECOND
MAX.
245°C
相關PDF資料
PDF描述
4128 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit
4129 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit
412D12M 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit
412D12MA 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit
412D18M 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit
相關代理商/技術參數
參數描述
4114R-1-104F 制造商:Bourns Inc 功能描述:
4114R-1-104LF 功能描述:電阻器網絡與陣列 14pin 100Kohms Isolated Low Profile RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel
4114R-1-105 功能描述:電阻器網絡與陣列 14 PIN ISO. 1M OHM RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel
4114R-1-105LF 功能描述:電阻器網絡與陣列 14pin 1Mohms Isolated Low Profile RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel
4114R-1-121 功能描述:電阻器網絡與陣列 14 PIN ISO. 120 OHM RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*