- 您現在的位置：買賣IC網 > PDF目錄351987 > 4114R-1-101 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit PDF資料下載
參數資料
| 型號： | 4114R-1-101 |
| 元件分類： | 復位半導體 |
| 英文描述： | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| 中文描述： | WIDERSTAND NETZWERK DICKFILM 100R 5ST |
| 文件頁數： | 43/62頁 |
| 文件大小： | 1883K |
| 代理商： | 4114R-1-101 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
Specifications are subject to change without notice.
324
FOR PRODUCT SPECIFICATIONS, SEE PAGES 309 - 311.
Typical Application
A typical application using a Bourns 801 RC Network in con-
junction with a 10K ECL design is shown below. Vee is typically
connected to -5.2 volts (10K ECL) or -4.5 volts (100K ECL). Vcc
is typically connected to GND. Vtt is typically connected to -2.0
volts. The 801 network shown below can terminate up to 6
transmission lines and provides a 0.01
F capacitor to reduce
cross talk and feedthrough effects.
The actual, effective delay and impedance due to
loading from stubs or additional devices off the line will be:
Tpd’ = Tpd √1 + Cd/Co
Zo
Zo’ =
√1 + (C
d/Co)
Where Co = intrinsic capacitance of the line
Cd = capacitance due to loading and stubs
off the line
Tpd = basic propagation delay of the line
Zo ....= basic impedance of the line
To formulate a guideline for when line termination is
necessary, take the ratio of the rise time or fall time and the two-
way delay along the line. The maximum length for unterminated
lines will result as follows:
Lmax =
Tr
2Tpd’
Where Tr = rise or fall time
Tpd = propagation delay per unit length
The above equation implies that the faster the edge rate or the
higher the loading on the line (i.e., higher fanout), the more likely
that termination will be necessary for a given line length.
Parallel Termination
For maximum circuit performance or distributed loads, parallel
termination is the most appropriate technique. A parallel termi-
nated line uses a resistor connected to -2 volts (ECL application)
at the receiving end. The resistor value matches the characteris-
tic impedance of the line (Zo), thereby producing zero reflection
at the receiver. In addition, the terminating resistor also provides
output pull down, so a separate pull down resistor at the driving
end is unnecessary.
Transmission Line Considerations
In high speed circuit applications, the signal propagation delay
(Tpd) and characteristic impedance (zo), along a printed circuit
board line must be taken into consideration. In general, if the
two-way delay along the line is greater than the rise or fall time
of the signal, then controlled impedance techniques (i.e., termi-
nation) must be utilized to prevent undesirable ringing or over-
and undershoots. The delay and impedance can be calculated
by knowing the intrinsic inductance (Lo) and capacitance (Co) of
the line:
Tpd = √LoCo
Zo =
√L
o/Co
Vcc1
Aout
A1in
Vee
Vcc2
Bout
B1in
A1in
A2in
B1in
B2in
A2in,
MC10H118 MECL 10KH
Vee
TRANSMISSION
LINES
Vtt
BOURNS 801
10K ECL TERMINATOR
Bourns Emitter Coupled Logic Terminator 800 Series
相關PDF資料 |
PDF描述 |
|---|---|
| 4114R-1-102 | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| 4114R-1-103 | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| 4114R-1-104 | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| 4128 | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| 4129 | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 4114R-1-101LF | 功能描述:電阻器網絡與陣列 14pin 100ohms Isolated Low Profile RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel |
| 4114R-1-102 | 功能描述:電阻器網絡與陣列 14 PIN ISO. 1.0K OHM RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel |
| 4114R-1-102LF | 功能描述:電阻器網絡與陣列 14pin 1Kohms Isolated Low Profile RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel |
| 4114R-1-103 | 功能描述:電阻器網絡與陣列 14 PIN ISO. 10K OHM RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel |
| 4114R-1-103LF | 功能描述:電阻器網絡與陣列 14pin 10Kohms Isolated Low Profile RoHS:否 制造商:Vishay/Thin Film 產品類型:Networks 電路類型:Divider 電阻器數量: 電阻數值:10 kOhms 容差:0.1 % 溫度系數: 管腳數量:3 工作溫度范圍:- 55 C to + 155 C 尺寸:1.02 mm W x 3.05 mm L x 1.4 mm H 引線間隔: 端接類型:SMD/SMT 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。