- 您現在的位置：買賣IC網 > PDF目錄358635 > 38C2 (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | 38C2 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 52/63頁 |
| 文件大?。?/td> | 1000K |
| 代理商： | 38C2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
52
38C2 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
NOTES ON PROGRAMMING
Processor Status Register
The contents of the processor status register (PS) after a reset are
undefined, except for the interrupt disable flag (I) which is
“
1.
”
After a
reset, initialize flags which affect program execution. In particular, it
is essential to initialize the index X mode (T) and the decimal mode
(D) flags because of their effect on calculations.
Interrupts
The contents of the interrupt request bits do not change immediately
after they have been written. After writing to an interrupt request reg-
ister, execute at least one instruction before performing a BBC or
BBS instruction.
Decimal Calculations
To calculate in decimal notation, set the decimal mode flag (D) to
“
1,
”
then execute an ADC or SBC instruction. After executing an
ADC or SBC instruction, execute at least one instruction before
executing an SEC, CLC, or CLD instruction.
In decimal mode, the values of the negative (N), overflow (V), and
zero (Z) flags are invalid.
Timers
If a value n (between 0 and 255) is written to a timer latch, the
frequency division ratio is 1/(n+1).
The timers share the one frequency divider to generate the count
source. Accordingly, when each timer starts operating, initializing
the frequency divider is not executed. Therefore, when the frequency
divider is selected for the count source, the delay of the maximum
one cycle of the count source is generated until the timer starts
counting or the waveform is output from timer starts operating. Also,
the count source cannot be checked externally.
Multiplication and Division Instructions
The index X mode (T) and the decimal mode (D) flags do not affect
the MUL and DIV instruction.
The execution of these instructions does not change the contents
of the processor status register.
Ports
The contents of the port direction registers cannot be read. The fol-
lowing cannot be used:
The data transfer instruction (LDA, etc.)
The operation instruction when the index X mode flag (T) is
“
1
”
The addressing mode which uses the value of a direction register
as an index
The bit-test instruction (BBC or BBS, etc.) to a direction register
The read-modify-write instructions (ROR, CLB, or SEB, etc.) to a
direction register.
Use instructions such as LDM and STA, etc., to set the port direction
registers.
Serial I/O
In clock synchronous serial I/O, if the receive side is using an exter-
nal clock and it is to output the S
RDY
signal, set the transmit enable
bit, the receive enable bit, and the S
RDY
output enable bit to
“
1.
”
Serial I/O continues to output the final bit from the T
X
D pin after trans-
mission is completed.
A-D Converter
The comparator uses internal capacitors whose charge will be lost if
the clock frequency is too low.
Therefore, make sure that f(X
IN
) is at least on 250 kHz (Note) during
an A-D conversion.
Note:
When the frequency divided by 2/4/8 is selected by the AD
conversion clock selection bits, the above frequency is multi-
plied by 2/4/8. Also, when the STP instruction is executed dur-
ing the A-D conversion, the A-D conversion is stopped imme-
diately, the A-D conversion completion bit is set to
“
1
”
, and the
interrupt request is generated.
LCD
When the LCD power input pin V
L3
is not used, connect it to V
CC
.
Instruction Execution Time
The instruction execution time is obtained by multiplying the number
of cycles shown in the list of machine instructions by the period of the
internal clock
φ
.
相關PDF資料 |
PDF描述 |
|---|---|
| 38D5 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 38F1222 | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
| TA5M | STECKER DIN MINI 5POL |
| 70B5031 | KUPPLUNG DIN MINI 5POL |
| 39-26-3050 | 300mA LDO Linear Regulators with Internal Microprocessor Reset Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 38C3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:38C3 Group USER＇S MANUALHardware Manual & Device User＇s Manual 1733K/APR.12.99 |
| 38C3_M | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 38000 SERIES |
| 38C8 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 38CAV4E | 功能描述:保險絲 38KV 4A CAV RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485 |
| 38CAVH0.5E | 功能描述:保險絲 38KV 0.5A CAV RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485 |
發布緊急采購，3分鐘左右您將得到回復。