- 您現在的位置：買賣IC網 > PDF目錄156551 > 37B77X (SMSC Corporation) ENHANCED SUPER I/O CONTROLLER WITH WAKE UP FEATURES PDF資料下載
參數資料
| 型號： | 37B77X |
| 廠商： | SMSC Corporation |
| 英文描述： | ENHANCED SUPER I/O CONTROLLER WITH WAKE UP FEATURES |
| 中文描述： | 增強型超I / O與向上特征喚醒控制器 |
| 文件頁數： | 4/196頁 |
| 文件大小： | 573K |
| 代理商： | 37B77X |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁
101
removed or added from/to the
FIFO
does
not
cross
the
threshold.
The interrupt generated is ISA friendly in that it
must pulse the interrupt line low, allowing for
interrupt sharing.
After a brief pulse low
following the interrupt event, the interrupt line is
tri-stated so that other interrupts may assert.
An interrupt is generated when:
1. For DMA transfers: When serviceIntr is 0,
dmaEn is 1 and the DMA TC is received.
2. For Programmed I/O:
a.
When serviceIntr is 0, dmaEn is 0,
direction
is
0
and
there
are
writeIntrThreshold or more free bytes in
the
FIFO.
Also,
an
interrupt
is
generated when serviceIntr is cleared
to
0
whenever
there
are
writeIntrThreshold or more free bytes in
the FIFO.
b.(1)
When serviceIntr is 0, dmaEn
is 0, direction is 1 and there
are readIntrThreshold or more
bytes in the FIFO.
Also, an
interrupt is generated when
serviceIntr is cleared to 0
whenever
there
are
readIntrThreshold
or
more
bytes in the FIFO.
3. When nErrIntrEn is 0 and nFault transitions
from high to low or when nErrIntrEn is set
from 1 to 0 and nFault is asserted.
4. When ackIntEn is 1 and the nAck signal
transitions from a low to a high.
FIFO Operation
The
FIFO
threshold
is
set
in
the
chip
configuration registers. All data transfers to or
from the parallel port can proceed in DMA or
Programmed I/O (non-DMA) mode as indicated
by the selected mode.
The FIFO is used by
selecting the Parallel Port FIFO mode or ECP
Parallel Port Mode. (FIFO test mode will be
addressed separately.) After a reset, the FIFO
is disabled. Each data byte is transferred by a
Programmed I/O cycle or PDRQ depending on
the selection of DMA or Programmed I/O mode.
The following paragraphs detail the operation of
the FIFO flow control.
In these descriptions,
<threshold>
ranges
from
1
to
16.
The
parameter FIFOTHR, which the user programs,
is one less and ranges from 0 to 15.
A low threshold value (i.e. 2) results in longer
periods of time between service requests, but
requires faster servicing of the request for both
read and write cases.
The host must be very
responsive to the service request.
This is the
desired case for use with a "fast" system.
A
high value of threshold (i.e. 12) is used with a
"sluggish" system by affording a long latency
period after a service request, but results in
more frequent service requests.
DMA TRANSFERS
DMA transfers are always to or from the
ecpDFifo, tFifo or CFifo.
DMA utilizes the
standard PC DMA services. To use the DMA
transfers, the host first sets up the direction and
state as in the programmed I/O case. Then it
programs the DMA controller in the host with the
desired count and memory address. Lastly it
sets dmaEn to 1 and serviceIntr to 0. The ECP
requests DMA transfers from the host by
activating the PDRQ pin. The DMA will empty
or fill the FIFO using the appropriate direction
and mode. When the terminal count in the DMA
controller is reached, an interrupt is generated
相關PDF資料 |
PDF描述 |
|---|---|
| 37C669 | DIODE SCHOTTKY SINGLE 25V 200mW 0.5V-vf 200mA-IFM 30mA-IF 2uA-IR SOD-323 3K/REEL |
| 37C672 | ENHANCED SUPER I/O CONTROLLER WITH FAST IR |
| 37C67X | ENHANCED SUPER I/O CONTROLLER WITH FAST IR |
| 37C957FR | ULTRA I/O CONTROLLER FOR PORTABLE APPLICATIONS |
| 37FMA1-ABW31N | SPECIAL SWITCH-PIEZO SWITCH, SPST, MOMENTARY, 0.2A, 24VDC, PANEL MOUNT-THREADED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 37B999 | 制造商:TE Connectivity 功能描述: |
| 37BCB34-4 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 37BK | 功能描述:烙鐵 Weller Modular Heatr Thread-on Tips 50W RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included |
| 37BMA-SMA-50-1 | 制造商:HUBER+SUHNER 功能描述:BETWEEN SERIES ADAPTER |
| 37BNC-50-0-1/3E | 制造商:HUBER+SUHNER 功能描述:BETWEEN SERIES ADAPTER |
發布緊急采購，3分鐘左右您將得到回復。