- 您現在的位置：買賣IC網 > PDF目錄41410 > 2DB52S (ITT CANNON) 52 CONTACT(S), FEMALE, D SUBMINIATURE CONNECTOR, CRIMP PDF資料下載
參數資料
| 型號： | 2DB52S |
| 廠商： | ITT CANNON |
| 元件分類： | D-微型連接器 |
| 英文描述： | 52 CONTACT(S), FEMALE, D SUBMINIATURE CONNECTOR, CRIMP |
| 封裝： | ROHS COMPLIANT |
| 文件頁數： | 2/10頁 |
| 文件大?。?/td> | 607K |
| 代理商： | 2DB52S |
69
www.ittcannon.com
Dimensions shown in inch (mm)
Specifications and dimensions subject to change
The Centi Line - .075" Contact Spacing
2D/CTA
CTA Assembly Instructions
.275 (6.98)
MAX.
.475 (12.06)
MAX.
INSERTION
Guide Posts
Polarizing Posts
1. Place the connector into the slot in the assembly block
with the arrows on the insulator pointing downward. The
connector will bottom against the internal shoulder in the
groove in the assembly block. Start contact insertion by
placing the crimped contact in the cavity by hard.
3. With firm steady pressure, push the contact into the
cavity until the resilient internal shoulder snaps into the
locking groove in the contact. To prevent over insertion,
the tool tip bottoms against the rear of the insulator.
4. The guide post and polarizing posts are inserted in teh
same manner as the contacts. The guide posts are inserted
into the socket insulator, and the polarizing posts are
inserted into the pin insulartor. The corresponding contact
in the mating insulator must be removed for each.
2. Position the insertion tool tip on the rear of contact as
shown. The insulation must be pulled back from the crimp
pot approximately 1/32" to allow the tool tip to butt
against the contact crimp pot.
EXTRACTION
1. To extract the contacts, place the conector face up in
the assembly block so that the contact to be extracted is
in the end of the block that has a fully slotted opening.
2. The pin extraction tool tip is tubular, slides over the pin
bundle and butts against the front shoulder of the pin. The
socket extraction tool is a solid rod that fits into the socket
contact, the external shoulder butts against the contact
socket shoulder.
3. Insert the extraction tool into the cavity and apply firm
pressure until the contact is pushed thru the rear of the
connector.
4. Lift the insulator from the groove and pull the contact
out. Repeat for balance of contacts to be removed.
相關PDF資料 |
PDF描述 |
|---|---|
| 2DC79P | 79 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, CRIMP |
| 2DC79SBRP | 79 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, SOLDER |
| 2DC79S | 79 CONTACT(S), FEMALE, D SUBMINIATURE CONNECTOR, CRIMP |
| 2DD100P | 100 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, CRIMP |
| 2DD100SBRP | 100 CONTACT(S), MALE, D SUBMINIATURE CONNECTOR, SOLDER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 2DB-52S | 制造商:ITT Interconnect Solutions 功能描述:MICRO DB 52POS SKT 制造商:ITT Interconnect Solutions 功能描述:Connector,D-Shell,Cable Mount,PLUG,52 Contacts,SKT,0.075 Pitch,IDC Terminal,HOLE .112-.124 |
| 2DB-52S-1 | 制造商:ITT Interconnect Solutions 功能描述:2DB-52S-1 - Bulk |
| 2DB52S-13 | 制造商:ITT Interconnect Solutions 功能描述:2DB52S-13 - Bulk |
| 2DB52S-1-F172 | 制造商:ITT Interconnect Solutions 功能描述:2DB52S-1-F172 / 096438-0002 / Micro |
| 2DB52S-20-FO | 制造商:ITT Interconnect Solutions 功能描述:2DB52S-20-FO - Bulk |
發布緊急采購，3分鐘左右您將得到回復。