參數資料
型號： 29LV320BTC-70
廠商： Macronix International Co., Ltd.
英文描述： 32 BIT 4M X 8 / 2M X 16 ] SINGLE VOLTAGE 3V ONLY FLASH MEMORY
中文描述： 32位4米× 8 / 2米× 16]單電壓3V時僅閃存
文件頁數： 18/63頁
文件大小： 949K
代理商： 29LV320BTC-70
18
P/N:PM0742
REV. 1.4, JUL. 04, 2003
MX29LV320T/B
verifies the programmed cell margin. Table 3 shows the
address and data requirements for the byte/word program
command sequence.
When the Embedded Program algorithm is complete, the
device then returns to reading array data and addresses
are no longer latched. The system can determine the
status of the program operation by using Q7, Q6, or RY/
BY. See "Write Operation Status" for information on these
status bits.
Any commands written to the device during the Em-
bedded Program Algorithm are ignored. Note that a
hardware reset immediately terminates the programming
operation. The Byte/Word Program command sequence
should be reinitiated once the device has reset to reading
array data, to ensure data integrity.
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed from a
"0" back to a "1". Attempting to do so may cause the
device to set Q5 to "1" ,” or cause the Data Polling
algorithm to indicate the operation was successful.
Pins
A0
A1
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q0
Code (Hex)
Manufacture code
VIL
VIL
1
1
0
0
0
0
1
0
C2H
Device code for MX29LV320T
VIH
VIL
1
0
1
0
0
1
1
1
22A7H
Device code for MX29LV320B
VIH
VIL
1
0
1
0
1
0
0
0
22A8H
TABLE 4. SILICON ID CODE
AUTOMATIC CHIP/SECTOR ERASE COMMAND
The device does not require the system to preprogram
prior to erase. The Automatic Erase algorithm automati-
cally preprograms and verifies the entire memory for an
all zero data pattern prior to electrical erase. The system
is not required to provide any controls or timings during
these operations. Table 3 shows the address and data
requirements for the chip erase command sequence.
Any commands written to the chip during the Automatic
Erase algorithm are ignored. Note that a hard-ware reset
during the chip erase operation immediately terminates
the operation. The Chip Erase command sequence should
However, a succeeding read will show that the data is
still "0". Only erase operations can convert a "0" to a
"1".
SETUP AUTOMATIC CHIP/SECTOR ERASE
Chip erase is a six-bus cycle operation. There are two
"unlock" write cycles. These are followed by writing the
"set-up" command 80H. Two more "unlock" write cycles
are then followed by the chip erase command 10H, or
the sector erase command 30H.
The MX29LV320T/B contains a Silicon-ID-Read opera-
tion to supplement traditional PROM programming meth-
odology. The operation is initiated by writing the read
silicon ID command sequence into the command regis-
ter. Following the command write, a read cycle with
A1=VIL,A0=VIL retrieves the manufacturer code of C2H.
A read cycle with A1=VIL, A0=VIH returns the device
code of A7H/A8H for MX29LV320T/B.
be reinitiated once the device has returned to reading
array data, to ensure data integrity.
The system can determine the status of the erase op-
eration by using Q7, Q6, Q2, or RY/BY. See "Write Op-
eration Status" for information on these status bits. When
the Automatic Erase algorithm is complete, the device
returns to reading array data and addresses are no longer
latched.
Figure 5 illustrates the algorithm for the erase opera-
tion.See the Erase/Program Operations tables in "AC
Characteristics" for parameters, and to Figure 4 for tim-
ing diagrams.
相關PDF資料
PDF描述
29LV400C-55R 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
29LV400C-70 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
29LV400C-90 4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
29LV650 64M (4M x 16) BIT
29LV800BB-70 8M-BIT [1Mx8/512K x16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
相關代理商/技術參數
參數描述
29LV400BA 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:4 Megabit (512 K x 8-Bit/256 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory
29LV400C-55R 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
29LV400C-70 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
29LV400C-90 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512K x 8 / 256K x 16] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY
29LV51215JU 制造商: 功能描述: 制造商:undefined 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*