- 您現在的位置：買賣IC網 > PDF目錄371439 > 29F040C-55 (Macronix International Co., Ltd.) 4M-BIT [512K x 8] CMOS SINGLE VOLTAGE 5V ONLY EQUAL SECTOR FLASH MEMORY PDF資料下載
參數資料
| 型號： | 29F040C-55 |
| 廠商： | Macronix International Co., Ltd. |
| 英文描述： | 4M-BIT [512K x 8] CMOS SINGLE VOLTAGE 5V ONLY EQUAL SECTOR FLASH MEMORY |
| 中文描述： | 4分位[為512k × 8] CMOS單電壓5V只等于部門閃存 |
| 文件頁數： | 9/38頁 |
| 文件大?。?/td> | 592K |
| 代理商： | 29F040C-55 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
9
P/N:PM1201
REV. 1.0, DEC. 20, 2005
MX29F040C
ERASE SUSPEND
This command only has meaning while the state ma-
chine is executing Automatic Sector Erase operation, and
therefore will only be responded during Automatic Sector
Erase operation. When the Erase Suspend command is
written during a sector erase operation, the device re-
quires a maximum of 20us to suspend the erase opera-
tions. However, When the Erase Suspend command is
written during the sector erase time-out, the device im-
mediately terminates the time-out period and suspends
the erase operation. After this command has been ex-
ecuted, the command register will initiate erase suspend
mode. The state machine will return to read mode auto-
matically after suspend is ready. At this time, state ma-
chine only allows the command register to respond to
the Read Memory Array, Erase Resume and program
commands.
The system can determine the status of the program
operation using the Q7 or Q6 status bits, just as in the
standard program operation. After an erase-suspend pro-
gram operation is complete, the system can once again
read array data within non-suspended sectors.
ERASE RESUME
This command will cause the command register to clear
the suspend state and return back to Sector Erase mode
but only if an Erase Suspend command was previously
issued. Erase Resume will not have any effect in all
other conditions. Another Erase Suspend command can
be written after the chip has resumed erasing. However,
a 400us time delay must be required after the erase re-
sume command, if the system implements an endless
erase suspend/resume loop, or the number of erase sus-
pend/resume is exceeded 1024 times. The erase times
will be expended if the erase behavior always be sus-
pended.
SET-UP AUTOMATIC PROGRAM COMMANDS
To initiate Automatic Program mode, A three-cycle com-
mand sequence is required. There are two "unlock" write
cycles. These are followed by writing the Automatic Pro-
gram command A0H.
Once the Automatic Program command is initiated, the
next WE# or CE# pulse causes a transition to an active
programming operation. Addresses are latched on the
falling edge, and data are internally latched on the
rising edge of the WE# or CE#, whichever happens first
pulse. The rising edge of WE# or CE#, whichever hap-
pens first also begins the programming operation. The
system is not required to provide further controls or tim-
ings. The device will automatically provide an adequate
internally generated program pulse and verify margin.
If the program operation was unsuccessful, the data on
Q5 is "1"(see Table 4), indicating the program operation
exceed internal timing limit. The automatic programming
operation is completed when the data read on Q6 stops
toggling for two consecutive read cycles and the data on
Q7 and Q6 are equivalent to data written to these two
bits, at which time the device returns to the Read mode
(no program verify command is required).
DATA# POLLING-Q7
The MX29F040C also features Data# Polling as a method
to indicate to the host system that the Automatic Pro-
gram or Erase algorithms are either in progress or com-
pleted.
While the Automatic Programming algorithm is in opera-
tion, an attempt to read the device will produce the comple-
ment data of the data last written to Q7. Upon comple-
tion of the Automatic Program Algorithm an attempt to
read the device will produce the true data last written to
Q7. The Data# Polling feature is valid after the rising
edge of the fourth WE# or CE#, whichever happens first
pulse of the four write pulse sequences for automatic pro-
gram.
While the Automatic Erase algorithm is in operation, Q7
will read "0" until the erase operation is competed. Upon
completion of the erase operation, the data on Q7 will
read "1". The Data# Polling feature is valid after the ris-
ing edge of the sixth WE# or CE#, whichever happens
first pulse of six write pulse sequences for automatic
chip/sector erase.
The Data# Polling feature is active during Automatic Pro-
gram/Erase algorithm or sector erase time-out. (see sec-
tion Q3 Sector Erase Timer)
相關PDF資料 |
PDF描述 |
|---|---|
| 29F040C-70 | 4M-BIT [512K x 8] CMOS SINGLE VOLTAGE 5V ONLY EQUAL SECTOR FLASH MEMORY |
| 29F040C-90 | 4M-BIT [512K x 8] CMOS SINGLE VOLTAGE 5V ONLY EQUAL SECTOR FLASH MEMORY |
| 29F080-12 | 8M-BIT [1024K x 8] CMOS EQUAL SECTOR FLASH MEMORY |
| 29F080-70 | 8M-BIT [1024K x 8] CMOS EQUAL SECTOR FLASH MEMORY |
| 29F080-90 | 8M-BIT [1024K x 8] CMOS EQUAL SECTOR FLASH MEMORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29F040C-70 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512K x 8] CMOS SINGLE VOLTAGE 5V ONLY EQUAL SECTOR FLASH MEMORY |
| 29F040C-90 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:4M-BIT [512K x 8] CMOS SINGLE VOLTAGE 5V ONLY EQUAL SECTOR FLASH MEMORY |
| 29F0418-0SR (900PC RL) | 制造商:Laird Technologies Inc 功能描述:SMD,6.1X4.5MM,6A I MAX,83 OHM,GULL WING,4 LINES,-55-+125,BLK - Tape and Reel |
| 29F0418-0SR-10 | 功能描述:信號調節 83ohms 100MHz 6A Thru-hole RoHS:否 制造商:EPCOS 產品:Duplexers 頻率:782 MHz, 751 MHz 頻率范圍: 電壓額定值: 帶寬: 阻抗:50 Ohms 端接類型:SMD/SMT 封裝 / 箱體:2.5 mm x 2 mm 工作溫度范圍:- 30 C to + 85 C 封裝:Reel |
| 29F0418-1SR | 功能描述:FERRITE 6A 119 OHM SMD RoHS:否 類別:濾波器 >> 鐵氧體磁珠和芯片 系列:- 標準包裝:1,000 系列:EMI1812 頻率對應阻抗:120 歐姆 @ 100MHz 額定電流:200mA DC 電阻(DCR):最大 400 毫歐 濾波器類型:差模 - 單線 封裝/外殼:1812（4532 公制） 安裝類型:表面貼裝 包裝:帶卷 (TR) 高度（最大）:0.069"（1.75mm） 尺寸/尺寸:0.177" L x 0.126" W（4.50mm x 3.20mm） 其它名稱:Q1712807A |
發布緊急采購，3分鐘左右您將得到回復。