- 您現在的位置：買賣IC網 > PDF目錄368963 > 295A910 INSTALLATION TESTER CHECKBOX16 PDF資料下載
參數資料
| 型號： | 295A910 |
| 英文描述： | INSTALLATION TESTER CHECKBOX16 |
| 中文描述： | 安裝測試儀CHECKBOX16 |
| 文件頁數： | 5/12頁 |
| 文件大?。?/td> | 94K |
| 代理商： | 295A910 |
2961
HIGH-CURRENT
HALF-BRIDGE
PRINTHEAD/MOTOR DRIVER
A logic high on the MODE pin sets the
current-control circuitry into the fast-decay
mode. When the peak current threshold is
detected, the flip-flop is reset and both the
source driver and the sink driver turn OFF.
Load current decays quickly through the
external ground clamp diode, the load, and
the internal flyback diode. In the fast-
decay mode, the OFF time period is one-
half the time that is set by the external RC
network for the slow-decay mode:
t
OFF
=
The amount of ripple current, when
chopping in the fast-decay mode, is
considerably higher than when chopping in
the slow-decay mode.
The frequency of the PWM current
control is determined by the time required
for the load current to reach the set peak
threshold (a function of the load character-
istics and V
BB
) plus the OFF time of the
switching driver(s) (set by the external RC
components).
To prevent false resetting of the flip-
flop, due to switching transients and noise,
a blanking time for the comparator can be
set by the user where t
B
≈
3600 x C in the
slow-decay mode or t
B
≈
2400 x C in the
fast-decay mode. For C between 100 pF
and 1000 pF, t
B
is in
μ
s.
POWER CONSIDERATIONS
The UDN2961B/W outputs are opti-
mized for low power dissipation. The sink
driver has a maximum saturation voltage
drop of only 1.4 V at 3.4 A, while the
source driver has a 2.2 V drop at -3.4 A.
Device power dissipation is minimized in
the slow-decay mode, as the chopping
driver (the source driver) is ON for less
than 50% of the chop period. When the
source driver is OFF during a chop cycle,
power is dissipated on chip only by the sink
driver; the rest of the power is dissipated
through the external ground clamp diode.
In the fast-decay mode, the ON time of the
chopping drivers (both the source driver
and the sink driver) may be greater than 50%, and the power dissipa-
tion will be greater.
GENERAL
A logic low on the ENABLE pin prevents the source driver and the
sink driver from turning ON, regardless of the state of the INPUT pin or
the supply voltages. With the ENABLE pin high, a logic low on the
INPUT pin turns ON the output drivers.
To protect against inductive load voltage transients, an external
ground clamp diode is required. A fast-recovery diode is recom-
mended to reduce power dissipation in the UDN2961B/W. The blank-
ing time prevents false triggering of the current sense comparator,
which can be caused by the recovery current spike of the ground
clamp diode when the chopping source driver turns ON.
RC
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
V
CC
V
BB
CURRENT-
CONTROL
LOGIC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
V
CC
CURRENT-
CONTROL
LOGIC
2940
±
1%
V
REF
INPUT
ENABLE
MODE
V
BB
V
BB
V
BB
R
C
R
C
Dwg. EP-038A
+5 V
+5 V
INPUT
47
μ
F
47
μ
F
2
±
1
BB
V
BB
V
相關PDF資料 |
PDF描述 |
|---|---|
| 2961 | HIGH-CURRENT HALF-BRIDGE PRINTHEAD/MOTOR DRIVER.WITH INTERNAL CURRENT SENSING AND CONTROL |
| 2961-0.5 | 5-Pin, Multiple-Input, Programmable Reset ICs |
| 2961-2G | 5-Pin, Multiple-Input, Programmable Reset ICs |
| 2961-2R | PATCHKABEL RJ45 STECKER ROT 2M |
| 2961-2Y | 5-Pin, Multiple-Input, Programmable Reset ICs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 295-AAC-12K | 制造商:Yageo / Phycomp 功能描述: |
| 295-AAC-15K | 制造商:Yageo / Phycomp 功能描述: |
| 295-AAC-27K | 制造商:Yageo / Phycomp 功能描述: |
| 295-AAC-2K2 | 制造商:Yageo / Phycomp 功能描述: |
| 295-AAC-33K | 制造商:Yageo / Phycomp 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。