- 您現在的位置：買賣IC網 > PDF目錄371437 > 2931AM (National Semiconductor Corporation) Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection PDF資料下載
參數資料
| 型號： | 2931AM |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| 中文描述： | 無電容，NMOS管，150mA的低壓差穩壓器的反向電流保護 |
| 文件頁數： | 12/18頁 |
| 文件大小： | 361K |
| 代理商： | 2931AM |
Application Hints
One of the distinguishing factors of the LM2931 series regu-
lators is the requirement of an output capacitor for device
stability. The value required varies greatly depending upon
the application circuit and other factors. Thus some com-
ments on the characteristics of both capacitors and the regu-
lator are in order.
High frequency characteristics of electrolytic capacitors de-
pend greatly on the type and even the manufacturer.As a re-
sult, a value of capacitance that works well with the LM2931
for one brand or type may not necessary be sufficient with an
electrolytic of different origin. Sometimes actual bench test-
ing, as described later, will be the only means to determine
the proper capacitor type and value. Experience has shown
that, as a rule of thumb, the more expensive and higher qual-
ity electrolytics generally allow a smaller value for regulator
stability. As an example, while a high-quality 100 μF alumi-
num electrolytic covers all general application circuits, simi-
lar stability can be obtained with a tantalum electrolytic of
only 47μF. This factor of two can generally be applied to any
special application circuit also.
Another critical characteristic of electrolytics is their perfor-
mance over temperature. While the LM2931 is designed to
operate to 40C, the same is not always true with all elec-
trolytics (hot is generally not a problem). The electrolyte in
many aluminum types will freeze around 30C, reducing
their effective value to zero. Since the capacitance is needed
for regulator stability, the natural result is oscillation (and lots
of it) at the regulator output. For all application circuits where
cold operation is necessary, the output capacitor must be
rated to operate at the minimum temperature. By coinci-
dence, worst-case stability for the LM2931 also occurs at
minimum temperatures. As a result, in applications where
the regulator junction temperature will never be less than
25C, the output capacitor can be reduced approximately by
a factor of two over the value needed for the entire tempera-
ture range. To continue our example with the tantalum elec-
trolytic, a value of only 22μF would probably thus suffice. For
high-quality aluminum, 47μF would be adequate in such an
application.
Another regulator characteristic that is noteworthy is that sta-
bility decreases with higher output currents. This sensible
fact has important connotations. In many applications, the
LM2931 is operated at only a few milliamps of output current
or less. In such a circuit, the output capacitor can be further
reduced in value. As a rough estimation, a circuit that is re-
quired to deliver a maximum of 10mA of output current from
the regulator would need an output capacitor of only half the
value compared to the same regulator required to deliver the
full output current of 100mA. If the example of the tantalum
capacitor in the circuit rated at 25C junction temperature
and above were continued to include a maximum of 10mA of
output current, then the 22μF output capacitor could be re-
duced to only 10μF.
In the case of the LM2931CT adjustable regulator, the mini-
mum value of output capacitance is a function of the output
voltage. As a general rule, the value decreases with higher
output voltages, since internal loop gain is reduced.
At this point, the procedure for bench testing the minimum
value of an output capacitor in a special application circuit
should be clear. Since worst-case occurs at minimum oper-
ating temperatures and maximum operating currents, the en-
tire circuit, including the electrolytic, should be cooled to the
minimum temperature. The input voltage to the regulator
should be maintained at 0.6V above the output to keep inter-
nal power dissipation and die heating to a minimum.
Worst-case occurs just after input power is applied and be-
fore the die has had a chance to heat up. Once the minimum
value of capacitance has been found for the brand and type
of electrolytic in question, the value should be doubled for
actual use to account for production variations both in the ca-
pacitor and the regulator. (All the values in this section and
the remainder of the data sheet were determined in this fash-
ion.)
LM2931 micro SMD Light Sensitivity
When the LM2931 micro SMD package is exposed to bright
sunlight, normal office fluorescent light, and other LED’s, it
operates within the guaranteed limits specified in the electri-
cal characteristic table.
Definition of Terms
Dropout Voltage:
The input-output voltage differential at
which the circuit ceases to regulate against further reduction
in input voltage. Measured when the output voltage has
dropped 100 mV from the nominal value obtained at 14V in-
put, dropout voltage is dependent upon load current and
junction temperature.
Input Voltage:
The DC voltage applied to the input terminals
with respect to ground.
Input-Output Differential:
The voltage difference between
the unregulated input voltage and the regulated output volt-
age for which the regulator will operate.
Line Regulation:
The change in output voltage for a change
in the input voltage. The measurement is made under condi-
tions of low dissipation or by using pulse techniques such
that the average chip temperature is not significantly af-
fected.
Load Regulation:
The change in output voltage for a
change in load current at constant chip temperature.
Long Term Stability:
Output voltage stability under acceler-
ated life-test conditions after 1000 hours with maximum
rated voltage and junction temperature.
Output Noise Voltage:
The rms AC voltage at the output,
with constant load and no input ripple, measured over a
specified frequency range.
Quiescent Current:
That part of the positive input current
that does not contribute to the positive load current. The
regulator ground lead current.
Ripple Rejection:
The ratio of the peak-to-peak input ripple
voltage to the peak-to-peak output ripple voltage at a speci-
fied frequency.
Temperature Stability of V
O
:
The percentage change in
output voltage for a thermal variation from room temperature
to either temperature extreme.
L
www.national.com
12
相關PDF資料 |
PDF描述 |
|---|---|
| 2933C | Optoelectronic |
| 2953C | Optoelectronic |
| 2963C | Optoelectronic |
| 2936-120 | 3-PHASE BRUSHLESS DC MOTOR CONTROLLER/DRIVER |
| 2938.803.0018.0-000 | MOTOR DC GETRIEBE 18 1 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 2931AM-5.0 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Series Low Dropout Regulators |
| 2931AZ-5.0 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 2931C | 制造商:Motorola Inc 功能描述: |
| 293-1K | 功能描述:碳膜電阻器 - 透孔 1Kohms 5% RoHS:否 制造商:KOA Speer 電阻:100 Ohms 容差:5 % 功率額定值:2 W 電壓額定值: 溫度系數:350 PPM / C 系列: 尺寸:4.2 mm Dia. x 12 mm L 工作溫度范圍:- 55 C to + 200 C 封裝:Reel |
| 293-1K/REEL | 功能描述:碳膜電阻器 - 透孔 1Kohms 5% RoHS:否 制造商:KOA Speer 電阻:100 Ohms 容差:5 % 功率額定值:2 W 電壓額定值: 溫度系數:350 PPM / C 系列: 尺寸:4.2 mm Dia. x 12 mm L 工作溫度范圍:- 55 C to + 200 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。