- 您現在的位置：買賣IC網 > PDF目錄368957 > 28F016S3 Evaluation Kit for the MAX5950/MAX5951 PDF資料下載
參數資料
| 型號： | 28F016S3 |
| 英文描述： | Evaluation Kit for the MAX5950/MAX5951 |
| 中文描述： | 字節(jié)寬的SMART 3 FlashFile Memory系列4。 8。及16兆比特 |
| 文件頁數： | 45/59頁 |
| 文件大小： | 384K |
| 代理商： | 28F016S3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
E
3 VOLT ADVANCED+ BOOT BLOCK
45
PRODUCT PREVIEW
Start
Write C0H
(Protection Reg.
Program Setup)
Write Protect. Register
Address/Data
Read Status Register
SR.7 = 1
Full Status
Check if Desired
Program Complete
Read Status Register
Data (See Above)
V
PP
Range Error
Protection Register
Programming Error
Attempted Program to
Locked Register -
Aborted
Program Successful
SR.3, SR.4 =
SR.1, SR.4 =
SR.1, SR.4 =
FULL STATUS CHECK PROCEDURE
Bus Operation
Write
Write
Standby
Protection Program operations can only be addressed within the protection
register address space. Addresses outside the defined space will return an
error.
Repeat for subsequent programming operations.
SR Full Status Check can be done after each program or after a sequence of
program operations.
Write FFH after the last program operation to reset device to read array mode.
Bus Operation
Standby
Standby
SR.3 MUST be cleared, if set during a program attempt, before further
attempts are allowed by the Write State Machine.
SR.1, SR.3 and SR.4 are only cleared by the Clear Staus Register Command,
in cases of multiple protection register program operations before full status is
checked.
If an error is detected, clear the status register before attempting retry or other
error recovery.
No
Yes
1, 1
0,1
1,1
Command
Protection Program
Setup
Protection Program
Comments
Data = C0H
Data = Data to Program
Addr = Location to Program
Check SR.7
1 = WSM Ready
0 = WSM Busy
Command
Comments
SR.1 SR.3 SR.4
0 1 1 V
PP
Low
0 0 1 Prot. Reg.
Prog. Error
1 0 1 Register
Locked:
Aborted
Read
Status Register Data Toggle
CE# or OE# to Update Status
Register Data
Standby
Figure 17. Protection Register Programming Flowchart
相關PDF資料 |
PDF描述 |
|---|---|
| 28F016SC | Evaluation Kit/Evaluation System for the MAX5954L/MAX5954A |
| 28F032C3 | 3 VOLT ADVANCED+ BOOT BLOCK. 8-. 16-. 32-MBIT FLASH MEMORY FAMILY |
| 28F160F3 | 5V/3.3V or Adjustable, Low-Dropout, Low-IQ, 500mA Linear Regulators |
| 28F800F3 | 3 Volt Fast Boot Block Flash Memory(3 V 8M位快速引導塊閃速存儲器) |
| 28F160F3 | 16MBIT Fast Boot Block Flash Memory(16兆位的快速引導塊閃速存儲器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 28F016S5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:BYTE-WIDE SMART 5 FlashFile MEMORY FAMILY 4. 8. AND 16 MBIT |
| 28F016SA | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:28F016SA 16-MBIT (1 MBIT X 16, 2 MBIT X 8)FlashFile MEMORY |
| 28F016SA/DD28F032SA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:INFORMATION |
| 28F016SA-070 | 制造商:undefined 功能描述: |
| 28F016SC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:28F016SC - BYTE-WIDE SmartVoltage FlashFile MEMORY FAMILY 4. 8. AND 16 MBIT |
發(fā)布緊急采購，3分鐘左右您將得到回復。