- 您現在的位置：買賣IC網 > PDF目錄371429 > 27LV002CB-90 (Macronix International Co., Ltd.) 2M-BIT [256K x 8] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY PDF資料下載
參數資料
| 型號： | 27LV002CB-90 |
| 廠商： | Macronix International Co., Ltd. |
| 英文描述： | 2M-BIT [256K x 8] CMOS SINGLE VOLTAGE 3V ONLY FLASH MEMORY |
| 中文描述： | 200萬位[256K × 8] CMOS單電壓3V時僅閃存 |
| 文件頁數： | 10/58頁 |
| 文件大?。?/td> | 528K |
| 代理商： | 27LV002CB-90 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
10
P/N:PM1204
MX29LV002C/002NC T/B
REV. 1.0, JUN. 30, 2005
Pins
A0
A1
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q0
Code(Hex)
Manufacture code
VIL
VIL
1
1
0
0
0
0
1
0
C2H
Device code
VIH
VIL
1
0
1
1
1
0
0
1
59H
for MX29LV002CT
Device code
VIH
VIL
1
0
1
1
1
0
1
0
5AH
for MX29LV002CB
Sector Protection
X
VIH
0
0
0
0
0
0
0
1
01H (Protected)
Verification
X
VIH
0
0
0
0
0
0
0
0
00H (Unprotected)
TABLE 6. EXPANDED SILICON ID CODE
READING ARRAY DATA
The device is automatically set to reading array data
after device power-up. No commands are required to re-
trieve data. The device is also ready to read array data
after completing an Automatic Program or Automatic
Erase algorithm.
After the device accepts an Erase Suspend command,
the device enters the Erase Suspend mode. The sys-
tem can read array data using the standard read tim-
ings, except that if it reads at an address within erase-
suspended sectors, the device outputs status data. Af-
ter completing a programming operation in the Erase
Suspend mode, the system may once again read array
data with the same exception. See "Erase Suspend/
Erase Resume Commands" for more infor-mation on this
mode.
The system must issue the reset command to re-en-
able the device for reading array data if Q5 goes high, or
while in the autoselect mode. See the "Reset Command"
section, next.
RESET COMMAND
Writing the reset command to the device resets the de-
vice to reading array data. Address bits are don't care for
this command.
The reset command may be written between the se-
quence cycles in an erase command sequence before
erasing begins. This resets the device to reading array
data. Once erasure begins, however, the device ignores
reset commands until the operation is complete.
The reset command may be written between the se-
quence cycles in a program command sequence be-fore
programming begins. This resets the device to reading
array data (also applies to programming in Erase Sus-
pend mode). Once programming begins, however, the
device ignores reset commands until the operation is
complete.
The reset command may be written between the se-
quence cycles in an SILICON ID READ command se-
quence. Once in the SILICON ID READ mode, the reset
command must be written to return to reading array data
(also applies to SILICON ID READ during Erase Sus-
pend).
If Q5 goes high during a program or erase operation, writ-
ing the reset command returns the device to reading ar-
ray data (also applies during Erase Suspend).
相關PDF資料 |
PDF描述 |
|---|---|
| 27LV256-20ISO | 256K (32K x 8) Low-Voltage CMOS EPROM |
| 27LV256-25IP | 256K (32K x 8) Low-Voltage CMOS EPROM |
| 27LV256-25ISO | 256K (32K x 8) Low-Voltage CMOS EPROM |
| 27LV256-25L | 256K (32K x 8) Low-Voltage CMOS EPROM |
| 27LV256-25P | 256K (32K x 8) Low-Voltage CMOS EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 27LV256 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:256K (32K x 8) Low-Voltage CMOS EPROM |
| 27LV256_04 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:256K (32K x 8) Low-Voltage CMOS EPROM |
| 27LV256-20/25/30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EPROM |
| 27LV256-20/J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM |
| 27LV256-20/K | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM |
發布緊急采購，3分鐘左右您將得到回復。