- 您現在的位置：買賣IC網 > PDF目錄371428 > 27L2000-70R (Macronix International Co., Ltd.) 2M-BIT [256Kx8] CMOS EPROM PDF資料下載
參數資料
| 型號： | 27L2000-70R |
| 廠商： | Macronix International Co., Ltd. |
| 英文描述： | 2M-BIT [256Kx8] CMOS EPROM |
| 中文描述： | 200萬位[256Kx8]的CMOS存儲器 |
| 文件頁數： | 3/18頁 |
| 文件大?。?/td> | 1214K |
| 代理商： | 27L2000-70R |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
3
MX27L2000
REV. 3.2, AUG. 26, 2003
P/N: PM0372
SYSTEM CONSIDERATIONS
During the switch between active and standby
conditions, transient current peaks are produced on the
rising and falling edges of Chip Enable. The magnitude
of these transient current peaks is dependent on the
output capacitance loading of the device. At a minimum,
a 0.1 uF ceramic capacitor (high frequency, low inherent
inductance) should be used on each device between
Vcc and GND to minimize transient effects. In addition,
to overcome the voltage drop caused by the inductive
effects of the printed circuit board traces on EPROM
arrays, a 4.7 uF bulk electrolytic capacitor should be
used between VCC and GND for each eight devices.
The location of the capacitor should be close to where
the power supply is connected to the array.
NOTES:
1. VH = 12.0 V
±
0.5 V
2. X = Either VIH or VIL
3. A1 - A8 = A10 - A17 = VIL(For auto select)
4. See DC Programming Characteristics for VPP voltage during programming.
MODE SELECT TABLE
PINS
A0
X
X
X
X
X
X
X
VIL
VIH
MODE
Read
Output Disable
Standby (TTL)
Standby (CMOS)
Program
Program Verify
Program Inhibit
Manufacturer Code(3) VIL
Device Code(3)
CE
VIL
VIL
VIH
VCC
±
0.3V
VIL
VIL
VIH
OE
VIL
VIH
X
X
VIH
VIL
X
VIL
VIL
PGM
X
X
X
X
VIL
VIH
X
X
X
A9
X
X
X
X
X
X
X
VH
VH
VPP
VCC
VCC
VCC
VCC
VPP
VPP
VPP
VCC
VCC
OUTPUTS
DOUT
High Z
High Z
High Z
DIN
DOUT
High Z
C2H
20H
VIL
TWO-LINE OUTPUT CONTROL FUNCTION
To accommodate multiple memory connections, a two-
line control function is provided to allow for:
1. Low memory power dissipation,
2. Assurance that output bus contention will not
occur.
It is recommended that CE be decoded and used as the
primary device-selecting function, while OE be made a
common connection to all devices in the array and
connected to the READ line from the system control bus.
This assures that all deselected memory devices are in
their low-power standby mode and that the output pins
are only active when data is desired from a particular
memory device.
相關PDF資料 |
PDF描述 |
|---|---|
| 27L256-20 | 256K-BIT [32Kx8] LOW VOLTAGE OPERATION CMOS EPROM |
| 27L256-12 | 256K-BIT [32Kx8] LOW VOLTAGE OPERATION CMOS EPROM |
| 27L256-15 | 256K-BIT [32Kx8] LOW VOLTAGE OPERATION CMOS EPROM |
| 27L256-25 | 256K-BIT [32Kx8] LOW VOLTAGE OPERATION CMOS EPROM |
| 27L2AI | LinCMOSE PRECISION DUAL OPERATIONAL AMPLIFIERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 27L200BX | 制造商:Genteq 功能描述: |
| 27L256-12 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:256K-BIT [32Kx8] LOW VOLTAGE OPERATION CMOS EPROM |
| 27L256-15 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:256K-BIT [32Kx8] LOW VOLTAGE OPERATION CMOS EPROM |
| 27L256-20 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:256K-BIT [32Kx8] LOW VOLTAGE OPERATION CMOS EPROM |
| 27L256-25 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:256K-BIT [32Kx8] LOW VOLTAGE OPERATION CMOS EPROM |
發布緊急采購，3分鐘左右您將得到回復。