- 您現在的位置：買賣IC網 > PDF目錄371414 > 269-TYPE 1480 nm Pump Laser Module PDF資料下載
參數資料
| 型號： | 269-TYPE |
| 英文描述： | 1480 nm Pump Laser Module |
| 中文描述： | 1480波長泵浦激光模塊 |
| 文件頁數： | 5/8頁 |
| 文件大小： | 85K |
| 代理商： | 269-TYPE |
Data Sheet
June 2001
269-Type 1480 nm Pump Laser Module
5
Agere Systems Inc.
User Information
* A positive input into this pin cools the laser.
Fiber Characteristics
I
Length of fiber pigtail:
— 1.75 m ± 0.25 m
I
Standard fiber:
— Cladding OD: 125
μ
m ± 2
μ
m
— Acrylate buffer OD: 250
μ
m ± 15
μ
m
— Cut off wavelength: <1320 nm
I
Polarization-maintaining fiber:
— PANDA
— Cut off wavelength: <1400 nm
— Acrylate buffer: 400
μ
m
Table 4. Pin Information
Pin
Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Connection
TE Cooler (+)*
Thermistor
Monitor Anode (–Bias)
Monitor Cathode (+Bias)
Thermistor
No Connect
No Connect
No Connect
No Connect
Laser Anode (+)
Laser Cathode (–)
No Connect
Package Ground
TEC Cooler (–)
Mounting and Connections
CAUTION: This device is susceptible to damage as
a result of electrostatic discharge.
Proper precautions should be taken
during both handling and testing.
The base of the laser module (see Outline Diagram)
should be maintained at or below 75 °C (maximum)
during operation. Interfaces between the laser module
base and heat sink must be clean, and the use of a
thermal filler may be necessary.
Mounting Instructions
The minimum fiber bend radius is 1.0 in.
To avoid degradation in performance, mount the mod-
ule on the board as follows:
1. Place the bottom flange of the module on a flat heat
sink at least 0.5 in. x 1.180 in. (12.7 mm x 30 mm)
in size. The surface finish of the heat sink should be
better than 32
μ
in. (0.8
μ
m), and the surface flat-
ness must be better than 0.001 in. (25.4
μ
m). Using
thermal conductive grease is optional; however,
thermal performance may be improved if conductive
grease is applied between the bottom flange and
the heat sink.
2. Mount four #2-56 screws with Fillister heads
(M2-3 mm) at the four screw hole locations (see
Outline Diagram). The Fillister head diameter must
not exceed 0.140 in. (3.55 mm). Do not apply more
than 1 in./lb. of torque to the screws.
Figure 1. Circuit Schematic
1-675 (F).i
7
6
5
4
3
2
1
8
9
10
11
12
13
14
TH 10 k
TEC
ISOLATOR
(OPTIONAL)
–
+
+
–
相關PDF資料 |
PDF描述 |
|---|---|
| 2690RD05 | Analog IC |
| 2690RD12 | Analog IC |
| 2690RD15 | Analog IC |
| 2690RS03.3 | Analog IC |
| 2690RS05 | GSM900 and DCS1800/PCS1900 Dual-Band, Low-Noise Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 269X | 功能描述:電話連接器 3 OCND 1/4" RED RoHS:否 制造商:Switchcraft 標準:1/4 in 開關配置:Switched 型式:Female 位置/觸點數量: 端接類型:Solder 安裝風格:Chassis (Panel) 方向: |
| 269XA 10MIC DISC 1.25" | 功能描述:LAPPING FILM ALUM OXIDE 269XA RoHS:是 類別:工具 >> 光纖和配件 系列:Trizact™, 269XA MSDS 材料安全數據表:8234 MSDS 標準包裝:10 系列:* |
| 2-6A | 制造商:JST Manufacturing 功能描述:Terminal,2-6A |
| 26A00028 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 26A-03 | 制造商:Aeroflex / Inmet 功能描述:ATTENUATOR - FIXED COAXIAL |
發布緊急采購，3分鐘左右您將得到回復。