- 您現在的位置：買賣IC網 > PDF目錄371399 > 24LC65-P (Microchip Technology Inc.) 64K 2.5V I 2 C Smart Serial EEPROM PDF資料下載
參數資料
| 型號： | 24LC65-P |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 64K 2.5V I 2 C Smart Serial EEPROM |
| 中文描述： | 64K的2.5VI 2葷智能串行EEPROM |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 106K |
| 代理商： | 24LC65-P |
1996 Microchip Technology Inc.
DS21073E-page 7
24LC65
5.0
READ OPERATION
Read operations are initiated in the same way as write
operations with the exception that the R/W bit of the
slave address is set to one. There are three basic types
of read operations: current address read, random read,
and sequential read.
5.1
Current Address Read
The 24LC65 contains an address counter that main-
tains the address of the last word accessed, internally
incremented by one. Therefore, if the previous access
(either a read or write operation) was to address n (n is
any legal address), the next current address read oper-
ation would access data from address n + 1. Upon
receipt of the slave address with R/W bit set to one, the
24LC65 issues an acknowledge and transmits the eight
bit data word. The master will not acknowledge the
transfer but does generate a stop condition and the
24LC65 discontinues transmission (Figure 4-3).
5.2
Random Read
Random read operations allow the master to access
any memory location in a random manner. To perform
this type of read operation, first the word address must
be set. This is done by sending the word address to the
24LC65 as part of a write operation (R/W bit set to 0).
After the word address is sent, the master generates a
start condition following the acknowledge. This termi-
nates the write operation, but not before the internal
address pointer is set. Then the master issues the con-
trol byte again but with the R/W bit set to a one. The
24LC65 will then issue an acknowledge and transmit
the eight bit data word. The master will not acknowl-
edge the transfer but does generate a stop condition
which causes the 24LC65 to discontinue transmission
(Figure 4-4).
5.3
Sequential Read
Sequential reads are initiated in the same way as a ran-
dom read except that after the 24LC65 transmits the
first data byte, the master issues an acknowledge as
opposed to the stop condition used in a random read.
This acknowledge directs the 24LC65 to transmit the
next sequentially addressed 8 bit word (Figure 4-5).
Following the final byte transmitted to the master, the
master will NOT generate an acknowledge but will gen-
erate a stop condition.
To provide sequential reads the 24LC65 contains an
internal address pointer which is incremented by one at
the completion of each operation. This address pointer
allows the entire memory contents to be serially read
during one operation.
5.4
Contiguous Addressing Across
Multiple Devices
The device select bits A2, A1, A0 can be used to
expand the contiguous address space for up to 512K
bits by adding up to eight 24LC65's on the same bus. In
this case, software can use A0 of the control byte as
address bit A13, A1 as address bit A14, and A2 as
address bit A15.
5.5
Noise Protection
The SCL and SDA inputs have filter circuits which sup-
press noise spikes to assure proper device operation
even on a noisy bus. All I/O lines incorporate Schmitt
triggers for 400 KHz (Fast Mode) compatibility.
5.6
High Endurance Block
The location of the high-endurance block within the
memory map is programmed by setting the leading bit
7 (S/HE) of the configuration byte to 0. The upper bits
of the address loaded in this command will determine
which 4K block within the memory map will be set to
high endurance. This block will be capable of
10,000,000 ERASE/WRITE cycles typical (Figure 8-1).
Note:
The High Endurance Block cannot be
changed after the security option has been
set. If the H.E. block is not programmed by
the user, the default location is the highest
block of memory.
相關PDF資料 |
PDF描述 |
|---|---|
| 24LC65-SM | 64K 2.5V I 2 C Smart Serial EEPROM |
| 24LCS21A | 1K 2.5V Dual Mode I 2 C Serial EEPROM |
| 24LCS21 | 1K 2.5V Dual Mode I 2 C Serial EEPROM |
| 24LCS41A | 1K/4K 2.5V Dual Mode, Dual Port IIC Serial EEPROM(1K/4K位,2.5V雙模式,雙端口IIC串行EEPROM) |
| 24LCS41 | 1K/4K 2.5V Dual Mode, Dual Port IIC Serial EEPROM(1K/4K位,2.5V雙模式,雙端口IIC串行EEPROM) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24LC65T/SM | 功能描述:電可擦除可編程只讀存儲器 8kx8 - 2.5V Smart RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24LC65T/SMG | 功能描述:電可擦除可編程只讀存儲器 8kx8 - 2.5V Smart Lead Free Package RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24LC65T-I/SM | 功能描述:電可擦除可編程只讀存儲器 8kx8 - 2.5V Smart RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24LC65T-I/SMG | 功能描述:電可擦除可編程只讀存儲器 8kx8 - 2.5V Smart Industrial Temp RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24LCS21A/P | 功能描述:電可擦除可編程只讀存儲器 2.5V Dual Mode RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。