參數資料
型號: 24LC62-ST
廠商: Microchip Technology Inc.
英文描述: 1K/2K Software Addressable I 2 C ⑩ Serial EEPROM
中文描述: 1K/2K軟件尋址的I 2 C⑩串行EEPROM
文件頁數: 6/16頁
文件大小: 426K
代理商: 24LC62-ST
24LCS61/62
DS21226A-page 6
Preliminary
1997 Microchip Technology Inc.
4.0
FUNCTIONAL DESCRIPTION
The 24LCS61/62 supports a bi-directional 2-wire bus
and data transmission protocol compatible with the I
2
C
protocol. The device is configured to reside on a com-
mon I
2
C bus with up to 255 total 24LCS61/62 devices
on the bus. Each device has a unique serial number
assigned to it when delivered from the factory. In an
actual system, this serial number will be used to assign
a separate 8-bit ID byte to each device in the system.
After an ID byte is assigned to each device in the sys-
tem, standard read and write commands can be sent to
each device individually.
4.1
Device Serial Number
The device serial number is stored in a 48-bit (6 byte)
register that is separate from the data array. The serial
number register is non-volatile and cannot be changed
by the user. Before shipment from the factory, this reg-
ister is programmed with a unique value for every
device. The 48 bit register allows for 2.8
10
14
different
combinations. The serial number is used at power-up to
assign the device an ID byte which is then used for all
standard read and write commands sent to that specific
device.
4.2
Device ID Byte
The Device ID byte is an 8-bit value that provides the
means for every device on the bus to be accessed indi-
vidually. The ID byte is stored in a RAM register sepa-
rate from the data array. The ID byte register will always
default to address 00 upon power-up.
4.3
Device Addressing
Each command to the device must begin with a start
bit. A control byte is the first byte received following the
start condition from the master device (Figure 4-1). The
control byte consists of a four-bit control code, the OE
bit, and three command select bits. For the 24LCS61/
62, the control code is set to 0110 binary for all opera-
tions. The device will not acknowledge any commands
sent with any other control code. The next bit is the Out-
put Enable (OE) bit. This bit controls the operation of
the EDS pin. See Section 9.0 for more details. The last
three bits of the control byte are the command select
bits (C0-C2). The command select bits determine
which command will be executed. See Table 4-1. Fol-
lowing a valid control byte, the 24LCS61/62 will
acknowledge the command.
FIGURE 4-1:
CONTROL BYTE FORMAT
TABLE 4-1:
COMMAND CODES
Command
Command Select Bits
(C2 C1 C0)
Set Write Protection Fuse
Read
Write (Byte or Page)
Assign Address
Clear Address
000
001
010
100
110
1
0
1
0
OE
C2
C1
S
ACK
Control Code
Command Select
Bits
Acknowledge Bit
Start Bit
C0
Output Enable
Bit
相關PDF資料
PDF描述
24LC61-ISN 1K/2K Software Addressable I 2 C ⑩ Serial EEPROM
24LC61-IST 1K/2K Software Addressable I 2 C ⑩ Serial EEPROM
24LC61-P 1K/2K Software Addressable I 2 C ⑩ Serial EEPROM
24LC61-SN 1K/2K Software Addressable I 2 C ⑩ Serial EEPROM
24LC61-ST 1K/2K Software Addressable I 2 C ⑩ Serial EEPROM
相關代理商/技術參數
參數描述
24LC64-/SN 制造商:Microchip Technology Inc 功能描述:
24LC64-E/MNY 功能描述:電可擦除可編程只讀存儲器 64K 8K X 8 2.5V SER EE EXT RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
24LC64-E/MS 功能描述:電可擦除可編程只讀存儲器 8kx8 - 2.5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
24LC64-E/P 功能描述:電可擦除可編程只讀存儲器 8kx8 - 2.5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
24LC64-E/SM 功能描述:電可擦除可編程只讀存儲器 8kx8 - 2.5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8