- 您現在的位置：買賣IC網 > PDF目錄368881 > 24LC024IST Line Card Timing IC with Synchronous Ethernet Support PDF資料下載
參數資料
| 型號： | 24LC024IST |
| 英文描述： | Line Card Timing IC with Synchronous Ethernet Support |
| 中文描述： | I2C串行EEPROM的 |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 182K |
| 代理商： | 24LC024IST |
24LC024/24LC025
DS21210D-page 6
1999 Microchip Technology Inc.
5.0
DEVICE ADDRESSING
A control byte is the first byte received following the
start condition from the master device (Figure 5-1). The
control byte consists of a four bit control code; for the
24LC024/24LC025 this is set as 1010 binary for read
and write operations. The next three bits of the control
byte are the chip select bits (A2, A1, A0). The chip
select bits allow the use of up to eight 24LC024/
24LC025 devices on the same bus and are used to
select which device is accessed. The chip select bits in
the control byte must correspond to the logic levels on
the corresponding A2, A1, and A0 pins for the device to
respond. These bits are in effect the three most signifi-
cant bits of the word address.
The last bit of the control byte defines the operation to
be performed. When set to a one a read operation is
selected, and when set to a zero a write operation is
selected. Following the start condition, the 24LC024/
24LC025 monitors the SDA bus checking the control
byte being transmitted. Upon receiving a 1010 code
and appropriate chip select bits, the slave device out-
puts an acknowledge signal on the SDA line. Depend-
ing on the state of the R/W bit, the 24LC024/24LC025
will select a read or write operation.
FIGURE 5-1:
CONTROL BYTE FORMAT
5.1
Contiguous Addressing Across
Multiple Devices
The chip select bits A2, A1, A0 can be used to expand
the contiguous address space for up to 16K bits by add-
ing up to eight 24LC024/24LC025 devices on the same
bus. In this case, software can use A0 of the control
byte as address bit A8, A1 as address bit A9, and A2
as address bit A10. It is not possible to sequentially
read across device boundaries.
1
0
1
0
A2
A1
A0
S
ACK
R/W
Control Code
Chip Select
Bits
Slave Address
Acknowledge Bit
Start Bit
Read/Write Bit
This Material Copyrighted by Its Respective Manufacturer
相關PDF資料 |
PDF描述 |
|---|---|
| 24LC024P | I2C Serial EEPROM |
| 24LC024SN | Line Card Timing IC |
| 24LC024ST | Line Card Timing IC |
| 24LT100 | POLYFUSE㈢ Resettable PTCs |
| 24LT100S | POLYFUSE㈢ Resettable PTCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24LC024P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| 24LC024SN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| 24LC024ST | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| 24LC024T/SN | 功能描述:電可擦除可編程只讀存儲器 256x8 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24LC024T/ST | 功能描述:電可擦除可編程只讀存儲器 256x8 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。