參數資料
型號: 24LC01BMODULES
廠商: Microchip Technology Inc.
英文描述: Stand-Alone OCV-Based Fuel Gauge
中文描述: 1K/2K在ISO微型模塊的I2C串行EEPROM
文件頁數: 5/12頁
文件大小: 451K
代理商: 24LC01BMODULES
24LC01B/02B Modules
1997 Microchip Technology Inc.
DS21222A-page 5
4.0
BUS CHARACTERISTICS
4.1
Slave Address
After generating a START condition, the bus master
transmits the slave address consisting of a 4-bit device
code (1010) for the 24LC01B/02B, followed by three
don't care bits.
The eighth bit of slave address determines if the master
device wants to read or write to the 24LC01B/02B
(Figure 4-1).
The 24LC01B/02B monitors the bus for its correspond-
ing slave address all the time. It generates an acknowl-
edge bit if the slave address was true, and it is not in a
programming mode.
FIGURE 4-1:
CONTROL BYTE
ALLOCATION
5.0
WRITE OPERATION
5.1
Byte Write
Following the start signal from the master, the device
code (4 bits), the don't care bits (3 bits), and the R/W
bit, which is a logic low, is placed onto the bus by the
master transmitter. This indicates to the addressed
slave receiver that a byte with a word address will follow
after it has generated an acknowledge bit during the
ninth clock cycle. Therefore, the next byte transmitted
by the master is the word address and will be written
into the address pointer of the 24LC01B/02B. After
receiving another acknowledge signal from the
24LC01B/02B, the master device will transmit the data
word to be written into the addressed memory location.
The 24LC01B/02B acknowledges again and the master
generates a stop condition. This initiates the internal
write cycle, and during this time the 24LC01B/02B will
not generate acknowledge signals (Figure 5-1).
5.2
Page Write
The write control byte, word address, and the first data
byte are transmitted to the 24LC01B/02B in the same
way as in a byte write. But instead of generating a stop
condition, the master transmits up to eight data bytes to
the 24LC01B/02B, which are temporarily stored in the
on-chip page buffer and will be written into the memory
after the master has transmitted a stop condition. After
the receipt of each word, the three lower order address
pointer bits are internally incremented by one. The
higher order five bits of the word address remains con-
stant. If the master should transmit more than eight
words prior to generating the stop condition, the
address counter will roll over and the previously
received data will be overwritten. As with the byte write
operation, once the stop condition is received an inter-
nal write cycle will begin (Figure 5-2).
FIGURE 5-1:
BYTE WRITE
S
T
A
R
T
FIGURE 5-2:
BUS ACTIVITY
MASTER
PAGE WRITE
S
T
A
R
T
Operation
Control
Code
Chip
Select
R/W
Read
Write
1010
1010
XXX
XXX
1
0
X = Don’t care
R/W
A
1
0
1
0
X
X
X
READ/WRITE
START
SLAVE ADDRESS
S
P
S
T
O
P
BUS ACTIVITY
MASTER
SDA LINE
BUS ACTIVITY
A
C
K
A
C
K
A
C
K
CONTROL
BYTE
WORD
ADDRESS
DATA
S
P
SDA LINE
BUS ACTIVITY
S
T
O
P
CONTROL
BYTE
WORD
ADDRESS (n)
DATA n
DATAn + 7
DATAn + 1
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
相關PDF資料
PDF描述
24LC02BMODULES Single/Dual/Triple/Quad DS3/E3 Single-Chip Transceivers
24LC040-ESN 4K SPI ⑩ Bus Serial EEPROM
24AA040-EP 4K SPI ⑩ Bus Serial EEPROM
24AA040-ESN RAC15-SB(-E)(-ST) Series - Powerline Regulated AC-DC Converters; Output Voltage (Vdc): 15V; Features: Compact AC-DC Power Supply; 15 Watt PCB Mount Package; Universal Input Voltage Range; 4000VAC Isolation; Low Output Ripple and Noise; Short Circuit Protected; UL-60601 Certified for Medical Applications
24AA040-EST 4K SPI ⑩ Bus Serial EEPROM
相關代理商/技術參數
參數描述
24LC01B-MT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K/2K I 2 C ⑩ Serial EEPROMs in ISO Micromodules
24LC01BP 制造商:MICRO CHIP 功能描述:*
24LC01BSN 制造商:MICRO CHIP 功能描述:New
24LC01B-SN 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K I2Ca?¢ Serial EEPROM
24LC01BT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K I2C? Serial EEPROM