- 您現在的位置：買賣IC網 > PDF目錄371395 > 24C21 (Atmel Corp.) DIODE ZENER 5.6V 120MW SSSMINI2 PDF資料下載
參數資料
| 型號： | 24C21 |
| 廠商： | Atmel Corp. |
| 英文描述： | DIODE ZENER 5.6V 120MW SSSMINI2 |
| 中文描述： | 2線串行EEPROM |
| 文件頁數： | 6/13頁 |
| 文件大小： | 252K |
| 代理商： | 24C21 |
AT24C21
6
Bidirectional Mode (DDC2)
This mode supports a 2-wire, Bidirectional data transmis-
sion protocol. The AT24C21 can be switched into the Bidi-
rectional Mode by issuing a valid high to low transition on
the SCL pin (refer to Figure 3). After the device is in the
Bidirectional Mode, all inputs to the VCLK pin are ignored,
except when a logic high is required to enable write capa-
bility. All byte and page writes and byte and sequential
reads are supported in this mode.
Bidirectional Mode Operation
CLOCK and DATA TRANSITIONS:
The SDA pin is nor-
mally pulled high with an external device. Data on the SDA
pin may change only during SCL low time periods (refer to
Data Validity timing diagram). Data changes during SCL
high periods will indicate a start or stop condition as
defined below.
START CONDITION:
A high-to-low transition of SDA with
SCL high is a start condition which must precede any other
command (refer to Start and Stop Definition timing dia-
gram).
STOP CONDITION:
A low-to-high transition of SDA with
SCL high is a stop condition. After a read or write
sequence, the stop command will place the EEPROM in a
standby power mode (refer to Start and Stop Definition tim-
ing diagram).
ACKNOWLEDGE:
All addresses and data words are seri-
ally transmitted to and from the EEPROM in 8-bit words.
The EEPROM sends a zero to acknowledge that it has
received each word. This happens during the ninth clock
cycle.
Device Addressing
The AT24C21 requires an 8-bit device address word fol-
lowing a start condition to enable the chip for a read or
write operation (refer to Figure 4).
The device address word consists of a mandatory one,
zero sequence for the first four most significant bits as
shown. This is common to all the EEPROM devices.
The next three bits are don’t care for the AT24C21.
The eighth bit of the device address is the read/write opera-
tion select bit. A read operation is initiated if this bit is high
and a write operation is initiated if this bit is low.
Upon a compare of the device address, the EEPROM will
output a zero. If a compare is not made, the chip will return
to a standby state.
STANDBY MODE:
The AT24C21 features a low power
standby mode which is enabled: (a) upon power-up and (b)
after the receipt of the STOP bit and the completion of any
internal operations.
MEMORY RESET:
After an interruption in protocol, power
loss or system reset, any 2-wire part can be reset by follow-
ing these steps:
(a) Clock up to 9 cycles, (b) look for SDA high in each cycle
while SCL is high and then (c) create a start condition as
SDA is high.
Figure 3.
Mode Transition
相關PDF資料 |
PDF描述 |
|---|---|
| 24C256 | 256K IIC CMOS serial EEPROM(4.5~5.5V,256K位,100K擦寫周期,EEPROM) |
| 24C320-EP | 32K 5.0V SPI Bus Serial EEPROM |
| 24C320-ESN | 32K 5.0V SPI Bus Serial EEPROM |
| 24C320-EST | 32K 5.0V SPI Bus Serial EEPROM |
| 24C320-IP | 32K 5.0V SPI Bus Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24C21-10SC-2.5 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 24-C212-00 | 功能描述:IC 與器件插座 LOCK/EJECT DIP SCKT SURFACE MOUNT 24 PIN RoHS:否 制造商:Molex 產品:LGA Sockets 節距:1.02 mm 排數: 位置/觸點數量:2011 觸點電鍍:Gold 安裝風格:SMD/SMT 端接類型:Solder 插座/封裝類型:LGA 2011 工作溫度范圍:- 40 C to + 100 C |
| 24-C212-10 | 功能描述:IC 與器件插座 LOCK/EJECT DIP SCKT SOLDER TAIL 24 PINS RoHS:否 制造商:Molex 產品:LGA Sockets 節距:1.02 mm 排數: 位置/觸點數量:2011 觸點電鍍:Gold 安裝風格:SMD/SMT 端接類型:Solder 插座/封裝類型:LGA 2011 工作溫度范圍:- 40 C to + 100 C |
| 24-C212-11 | 功能描述:IC 與器件插座 LOCK/EJECT DIP SCKT SOLDER TAIL 24 PINS RoHS:否 制造商:Molex 產品:LGA Sockets 節距:1.02 mm 排數: 位置/觸點數量:2011 觸點電鍍:Gold 安裝風格:SMD/SMT 端接類型:Solder 插座/封裝類型:LGA 2011 工作溫度范圍:- 40 C to + 100 C |
| 24-C212-20 | 功能描述:IC 與器件插座 LOCK/EJECT DIP SCKT WIRE WRAP 24 PINS RoHS:否 制造商:Molex 產品:LGA Sockets 節距:1.02 mm 排數: 位置/觸點數量:2011 觸點電鍍:Gold 安裝風格:SMD/SMT 端接類型:Solder 插座/封裝類型:LGA 2011 工作溫度范圍:- 40 C to + 100 C |
發布緊急采購，3分鐘左右您將得到回復。