- 您現在的位置：買賣IC網 > PDF目錄368878 > 24C16 (Fairchild Semiconductor Corporation) 16K-Bit Standard 2-Wire Bus Interface Serial EEPROM PDF資料下載
參數資料
| 型號： | 24C16 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | 16K-Bit Standard 2-Wire Bus Interface Serial EEPROM |
| 中文描述： | 16K的位標準2線總線接口的串行EEPROM |
| 文件頁數： | 4/17頁 |
| 文件大小： | 126K |
| 代理商： | 24C16 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
AI01100
VCC
CBUS
SDA
RL
MASTER
RL
SCL
CBUS
100
200
300
400
0
4
8
12
16
20
CBUS (pF)
R
)
VCC = 5V
Figure 3. Maximum R
L
Value versus Bus Capacitance (C
BUS
) for an I
2
C Bus
SIGNALS DESCRIPTION
Serial Clock (SCL).
The SCL input signal is used
to synchronise all data in and out of the memory. A
resistor can be connected from the SCL line to V
CC
to act as a pull up (see Figure 3).
Serial Data (SDA).
The SDA signal is bi-directional
and is used to transfer data in or out of the memory.
It is an open drain output that may be wire-OR’ed
with other open drain or open collector signals on
the bus. A resistor must be connected from the SDA
bus line to V
CC
to act as pull up (see Figure 3).
Protected Block Select (PB0, PB1).
PB0 and PB1
input signals select the block in the upper part of
the memory where write protection starts. These
inputs have a CMOS compatible input level.
Protect Enable (PRE).
The PRE input signal, in
addition to the status of the Block Address Pointer
bit (b2, location 7FFh as in Figure 7), sets the PRE
write protection active.
Mode (MODE).
The MODE input is available on pin
7 (see also WC feature) and may be driven dynami-
cally. It must be at V
IL
or V
IH
for the Byte Write
mode, V
IH
for Multibyte Write mode or V
IL
for Page
Write mode. When unconnected, the MODE input
is internally read as V
IH
(Multibyte Write mode).
Write Control (WC).
An hardware Write Control
feature is offered only for ST24W16 and ST25W16
versions on pin 7. This feature is usefull to protect
the contents of the memory from any erroneous
erase/write cycle. The Write Control signal is used
to enable (WC at V
IH
) or disable (WC at V
IL
) the
internal write protection. When unconnected, the
WC input is internally read as V
IL
. The devices with
this Write Control feature no longer supports the
Multibyte Write mode of operation, however all
other write modes are fully supported.
Refer to the AN404 Application Note for more de-
tailed information about Write Control feature.
4/17
ST24/25C16, ST24/25W16
相關PDF資料 |
PDF描述 |
|---|---|
| 24C32AEP | I2C Serial EEPROM |
| 24C32AESM | I2C Serial EEPROM |
| 24C32AESN | I2C Serial EEPROM |
| 24C32AIP | I2C Serial EEPROM |
| 24C32AISM | I2C Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24C16/P | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| 24C16/SL | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| 24C160-EP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C160-ESN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C160-IP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8K/16K 5.0V SPI Bus Serial EEPROM |
發布緊急采購，3分鐘左右您將得到回復。