- 您現在的位置：買賣IC網 > PDF目錄368878 > 24C16 (Atmel Corp.) 2-Wire Serial EEPROM PDF資料下載
參數資料
| 型號： | 24C16 |
| 廠商： | Atmel Corp. |
| 元件分類： | EEPROM |
| 英文描述： | 2-Wire Serial EEPROM |
| 中文描述： | 2線串行EEPROM |
| 文件頁數： | 11/17頁 |
| 文件大?。?/td> | 126K |
| 代理商： | 24C16 |
Write Protection.
Data in the upper four blocks of
256 bytes of the memory may be write protected.
The memory is write protected between a boundary
address and the top of memory (address
7FFh).The boundary address is user defined by
writing it in the Block Address Pointer (location
7FFh).
The Block Address Pointer is an 8 bit EEPROM
register located at the address 7FFh. It is com-
posed by 4 MSBs Address Pointer, which defines
the bottom boundary address, and 4 LSBs which
must be programmed at ’0’. This Address Pointer
can therefore address a boundary by page of 16
bytes.
The block in which the Block Address Pointer de-
fines the boundary of the write protected memory
is defined by the logic level applied on the PB1 and
PB0 input pins:
– PB1 =’0’and PB0 =’0’ select block 4
– PB1 =’0’and PB0 =’1’ select block 5
– PB1 =’1’and PB0 =’0’ select block 6
– PB1 =’1’and PB0 =’1’ select block 7
The following sequence should be used to set the
Write Protection:
– write the data to be protected into the top of
the memory, up to, but not including, location
7FFh;
– select the block by hardwiring the signals PB0
& PB1;
– set the protection by writing the correct bottom
boundary address in the Address Pointer (4
MSBs of location 7FFh) with bit b2 (Protect
Flag) set to ’0’.
Note that for a correct fonctionality of the memory,
all the 4 LSBs of the Block Address Pointer must
also be programmed at ’0’. The area will be pro-
tected when the PRE input is taken High.
Remark:
The Write Protection is active if and only
if the PRE input pin is driven High and the bit 2 of
location 7FFh is set to ’0’. In all the other cases, the
memory Block will not be protected. While the PRE
input pin is read at ’0’ by the memory, the location
7FFh can be used as a normal EEPROM byte.
Caution:
Special attention must be used when
using the protect mode together with the Multibyte
Write mode (MODE input pin High). If the Multibyte
Write starts at the location right below the first byte
of the Write Protected area, then the instruction will
write over the first 7 bytes of the Write Protected
area. The area protected is therefore smaller than
the content defined in the location 7FFh, by 7 bytes.
This does not apply to the Page Write mode as the
address counter ’roll-over’ and thus cannot go
above the 16 bytes lower boundary of the protected
area.
S
S
BYTE WRITE
DEV SEL
BYTE ADDR
DATA IN
S
MULTIBYTE
AND
PAGE WRITE
DEV SEL
BYTE ADDR
DATA IN 1
DATA IN 2
AI00793
S
DATA IN N
ACK
ACK
ACK
R/W
ACK
ACK
ACK
R/W
ACK
ACK
Figure 9. Write Modes Sequence (ST24/25C16)
11/17
ST24/25C16, ST24/25W16
相關PDF資料 |
PDF描述 |
|---|---|
| 24C16 | 8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C160-EP | 8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C160-ESN | 8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C160-IP | 8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C160-ISN | 8K/16K 5.0V SPI Bus Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24C16/P | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| 24C16/SL | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| 24C160-EP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C160-ESN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C160-IP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8K/16K 5.0V SPI Bus Serial EEPROM |
發布緊急采購，3分鐘左右您將得到回復。