- 您現在的位置：買賣IC網 > PDF目錄368878 > 24C160-ESN (Microchip Technology Inc.) 8K/16K 5.0V SPI Bus Serial EEPROM PDF資料下載
參數資料
| 型號： | 24C160-ESN |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 8K/16K 5.0V SPI Bus Serial EEPROM |
| 中文描述： | 8K/16K 5.0V SPI總線串行EEPROM |
| 文件頁數： | 8/17頁 |
| 文件大小： | 126K |
| 代理商： | 24C160-ESN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
Stop Condition.
STOP is identified by a low to high
transition of the SDA line while the clock SCL is
stable in the high state. A STOP condition termi-
nates communication between the ST24/25x16
and the bus master. A STOP condition at the end
of a Read command forces the standby state. A
STOP condition at the end of a Write command
triggers the internal EEPROM write cycle.
Acknowledge Bit (ACK).
An acknowledge signal
is used to indicate a successful data transfer. The
bus transmitter, either master or slave, will release
the SDA bus after sending 8 bits of data. During the
9th clock pulse period the receiver pulls the SDA
bus low to acknowledge the receipt of the 8 bits of
data.
SCL
SDA
SCL
SDA
SDA
START
CONDITION
SDA
INPUT
SDA
CHANGE
AI00792
STOP
CONDITION
1
2
3
7
8
9
MSB
ACK
START
CONDITION
SCL
1
2
3
7
8
9
MSB
ACK
STOP
CONDITION
Figure 6. I
2
C Bus Protocol
Data Input.
During data input the ST24/25x16
samples the SDA bus signal on the rising edge of
the clock SCL. Note that for correct device opera-
tion the SDA signal must be stable during the clock
low to high transition and the data must change
ONLY when the SCL line is low.
Memory Addressing.
To start communication be-
tween the bus master and the slave ST24/25x16,
the master must initiate a START condition. The 8
bits sent after a START condition are made up of a
device select of 4 bits that identifie the device type
(1010), 3 Block select bits and one bit for a READ
(RW = 1) or WRITE (RW = 0) operation.
There are three modes both for read and write.
They are summarised in Table 4 and described
hereafter. A communication between the master
and the slave is ended with a STOP condition.
8/17
ST24/25C16, ST24/25W16
相關PDF資料 |
PDF描述 |
|---|---|
| 24C160-IP | 8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C160-ISN | 8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C160-P | 8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C160-SN | 8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C16 | 1K-bit/2K-bit/4K-bit/8K-bit/16K-bit 2-WIRE SERIAL CMOS EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24C160-IP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C160-ISN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C160-P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C160-SN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8K/16K 5.0V SPI Bus Serial EEPROM |
| 24C164 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-Wire Serial EEPROM |
發布緊急采購，3分鐘左右您將得到回復。