- 您現在的位置：買賣IC網 > PDF目錄370032 > 232266393025 (Vishay Intertechnology,Inc.) PTC Thermistors, Overload Protection For Telecommunication PDF資料下載
參數資料
| 型號： | 232266393025 |
| 廠商： | Vishay Intertechnology,Inc. |
| 元件分類： | 熱敏電阻 |
| 英文描述： | PTC Thermistors, Overload Protection For Telecommunication |
| 中文描述： | PTC熱敏電阻器，超載保護電信 |
| 文件頁數： | 2/4頁 |
| 文件大小： | 68K |
| 代理商： | 232266393025 |
2322 66. 9....
Vishay BCcomponents
PTC Thermistors, Overload Protection
For Telecommunication
www.vishay.com
164
For technical questions contact: nlr.europe@vishay.com
Document Number: 29070
Revision: 10-Oct-03
DIMENSIONS
in millimeters
COMPONENT OUTLINE
For dimensions see Specific Physical
Dimentions and Packaging table.
Lead pitch F = 5 mm +0.6/-0.1.
Lead thickness d = 0.6 mm ±10%.
CCB914
T
D
T
D
d
F
L
1
H
2
H
3
OVERCURRENT PROTECTION OF
TELECOMMUNICATION LINES
The PTC thermistor must protect the telephone line circuit
against overcurrent which may be caused by the following
examples:
Surges due to lightning strikes on or near to the line plant.
Short-term induction of alternating voltages from adjacent
power lines or railway systems, usually caused when these
lines or systems develop faults.
Direct contact between telephone lines and power lines.
To provide good protection under such conditions a PTC
thermistor is connected in series with each line, usually as
secondary protection; see Typical Telephone Line drawing
on page 1. However, even with primary line protection
(usually a gas discharge tube), the PTC thermistor must fulfil
severe requirements.
Surge pulses of up to 2 kV can occur and in order to
withstand short-term power induction the PTC thermistor
must withstand high voltages. If the line has primary
protection a 220 V to 300 V PTC thermistor is adequate.
Without primary protection, however, a 600 V PTC device is
necessary. Vishay BCcomponents manufacturers a range of
PTC thermistors (see Electrical Data and Ordering
Information Table ) covering both requirements.
In the case of direct contact between the telephone line and
a power line, the PTC thermistor must withstand very high
inrush power at normal mains voltage. Under such
conditions, overload currents of up to 10 A on a 230 V mains
could occur for up to several hours. To handle this power, the
resistance/temperature characteristic of the thermistor must
have a very steep slope and the ceramic must be extremely
homogeneous.
In case of overcurrent due to short-term induction of
alternating voltages, currents of several AMPs with voltages
as high as 650 V
RMS
can be present for several seconds
For standard high voltage applications, resistance values
from 25 to 50
are available. However, ISDN networks
which carry high-frequency sound and vision, need lower line
impedance.
Telecommunication designers are therefore demanding high
voltage thermistors with much lower R
places even greater demands on the manufacture of PTC
thermistors. For these applications PTC thermistors which
have a R
25
value of 10
300 to 600 V
RMS
range are available.
In a typical telephone line application, two PTC thermistors
are used, one each for the tip and ring (or A and B) wire
together with their series resistors. For good line balance it is
important that the thermistor and resistor pairs are matched.
25
values, which
with voltages in the
On request, Vishay BCcomponents can supply matched or
binned PTC thermistors with R
as 0.5
.
25
values matched to as close
SPECIFIC PHYSICAL DIMENSIONS AND PACKAGING
in millimeters
D
MAX.
T
MAX.
H
2
L
1
H
3
MAX.
PACKAGING
(1)(2)
CATALOG
NUMBER
2322 ... .....
7.0
8.5
7.0
6.7
7.0
8.3
6.8
11
11
6.7
7.0
13.6
8.3
4.0
5.0
4.0
4.0
5.0
4.0
4.3
4.5
4.5
1.8
4.0
6.0
5.0
3.5
1.5 to 3.0
2.0
±
1.5 to 3.0
1.5 to 3
1.5 to 3.0
1.5 to 3.0
4.0
±
4.0
±
2.0
±
4.0
±
1.5
±
±
0.5
±
±
11.0
11.5
9.8
10.0
10.0
11.0
10.1
15.5
15.5
9.8
18.6
10.3
taped H0 = 16 mm
taped H0 = 16 mm
taped H0 = 18 mm
taped H0 = 18 mm
taped H0 = 16 mm
taped H0 = 18 mm
taped H0 = 16 mm
taped H0 = 16 mm
taped H0 = 16 mm
disc on tray
taped H0 = 18 mm
bulk
bulk
661 91066
661 93048
661 93147
661 93025
661 93037
661 93175
661 93142
662 93081
662 93074
661 93118
661 93148
663 93025
661 93078
0.5
(3)
1.0
1.0
(3)
0.5
1.0
0.5
20
20
4.0
3.0
(3)
相關PDF資料 |
PDF描述 |
|---|---|
| 232267191 | PTC Thermistors, For Temperature Protection |
| 232267191002 | PTC Thermistors, For Temperature Protection |
| 232267191005 | PTC Thermistors, For Temperature Protection |
| 232267191007 | PTC Thermistors, For Temperature Protection |
| 232267191052 | PTC Thermistors, For Temperature Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 232267191 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:PTC Thermistors, For Temperature Protection |
| 232267191002 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:PTC Thermistors, For Temperature Protection |
| 232267191005 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:PTC Thermistors, For Temperature Protection |
| 232267191007 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:PTC Thermistors, For Temperature Protection |
| 232267191012 | 制造商:BERNIC 功能描述:PTC SS CHP 1717 140C 030 130 B e4 |
發布緊急采購，3分鐘左右您將得到回復。