- 您現在的位置：買賣IC網 > PDF目錄370029 > 20H04 (SMSC Corporation) 4-PORT USB2.0 HUB CONTROLLER PDF資料下載
參數資料
| 型號： | 20H04 |
| 廠商： | SMSC Corporation |
| 英文描述： | 4-PORT USB2.0 HUB CONTROLLER |
| 中文描述： | 4端口USB2.0集線器控制器 |
| 文件頁數： | 19/38頁 |
| 文件大?。?/td> | 919K |
| 代理商： | 20H04 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
4-Port USB2.0 Controller
Datasheet
SMSC USB20H04
Page 19
Revision 1.63 (10-14-04)
DATASHEET
Chapter 7
Functional Overview
Figure 2.1 shows the functional block diagram of the USB2.0 Hub Controller. Each of the functions is
described in detail below.
7.1
Bus-Power Detect
The VBUSDET pin on the USB20H04 monitors the state of the upstream V
BUS
signal and will not pull-up
the DP0 resistor if V
BUS
is not active. If V
BUS
goes from an active to an inactive state (not powered), the
USB20H04 will remove power from the DP0 pull-up resistor within 10 seconds.
To support a dual-role OTG host on the upstream port, the USB20H04 has the ability to pulse the inactive
V
BUS
line. This is defined as V
BUS
pulsing in the OTG specification. For a more detailed discussion of the
“Application Note 10.4 Using the USB20H04 with an OTG Host”.
7.2
Upstream PHY
The upstream PHY includes the transmitter and receiver that operate in high-speed or full-speed mode,
depending on the current hub configuration and the host. The required termination resistors are internal to
the USB20H04.
To support a dual-role OTG host on the upstream port, the USB20H04 has the ability to attach a 1.5K ohm
resistor to the DP0 pin for 5 to 10ms. This is defined as data-line pulsing in the OTG specification.
7.3
Clock/PLL
The USB20H04 requires a 24MHz signal as a reference clock for the internal PLL. An external crystal is
used with the internal oscillator, or an external clock signal can be provided.
7.4
Internal Configuration Select
A default configuration for the USB20H04 is present immediately after RESET_N negation. When the
default configuration values will not be used, user defined values must be provided from an external source
via the serial interface. The user defined values to be configured are described in section 8.2.
See Section 8.1 for typical circuit examples showing how to select either the default configuration or an
external EEPROM. The pins used to select the source of configuration values are given in Table 4.2.
The internal default configuration is enabled when SMB_SEL_N is high and CS/EE_SEL is low on the
rising edge of RESET_N. When the SELF_PWR pin is low on the rising edge of RESET_N, the
bus-powered default configuration is loaded. If the SELF_PWR pin is high, the self-powered default
configuration is loaded. This allows the default configuration to be bus-powered or self-powered following a
reset.
相關PDF資料 |
PDF描述 |
|---|---|
| 20N60BD1 | HiPerFAST IGBT with Diode |
| 20N60B | HiPerFAST IGBT |
| 20S207DA4 | VACUUM FLUORESCENT DISPLAY MODULE |
| 20SVP150M | OS-CON SVP series |
| 20SVP22M | SVP series |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 20H07-660 | 功能描述:保險絲 20AMP 660VAC/250VDC RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485 |
| 20H07C | 功能描述:保險絲 20A CANADIAN RoHS:否 制造商:Littelfuse 產品:Surface Mount Fuses 電流額定值:0.5 A 電壓額定值:600 V 保險絲類型:Fast Acting 保險絲大小/組:Nano 尺寸:12.1 mm L x 4.5 mm W 安裝風格: 端接類型:SMD/SMT 系列:485 |
| 20H07CB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Fuse |
| 20H18A | 制造商: 功能描述: 制造商:TE Connectivity / Deutsch 功能描述: 制造商:undefined 功能描述: |
| 20H-20F | 制造商:Panasonic Industrial Company 功能描述:CABLE |
發布緊急采購，3分鐘左右您將得到回復。