參數資料
型號： 20-101-1154
廠商： Rabbit Semiconductor
文件頁數： 106/112頁
文件大小： 0K
描述： MODULE RCM4120 RABBITCORE
標準包裝： 1
系列： RabbitCore®
模塊/板類型： MPU 核心模塊
適用于相關產品： RCM4120
其它名稱： 316-1122
User’s Manual
89
B.4.1 Adding Other Components
There are pads for 28-pin TSSOP devices, 16-pin SOIC devices, and 6-pin SOT devices
that can be used for surface-mount prototyping with these devices. There are also pads that
can be used for SMT resistors and capacitors in an 0805 SMT package. Each component
has every one of its pin pads connected to a hole in which a 30 AWG wire can be soldered
(standard wire wrap wire can be soldered in for point-to-point wiring on the Prototyping
Board). Because the traces are very thin, carefully determine which set of holes is con-
nected to which surface-mount pad.
B.4.2 Measuring Current Draw
The Prototyping Board has a current-measurement feature available at header locations
JP1 and JP2 for the +5 V and +3.3 V supplies respectively. To measure current, you will
have to cut the trace on the bottom side of the Prototyping Board corresponding to the
power supply or power supplies whose current draw you will be measuring. Header loca-
tions JP1 and JP2 are shown in Figure B-5. Then install a 1 × 2 header strip from the
Development Kit on the top side of the Prototyping Board at the header location(s) whose
trace(s) you cut. The header strip(s) will allow you to use an ammeter across their pins to
measure the current drawn from that supply. Once you are done measuring the current,
place a jumper across the header pins to resume normal operation.
Figure B-5. Prototyping Board Current-Measurement Option
NOTE: Once you have cut the trace below header location JP1 or JP2, you must either be
using the ammeter or have a jumper in place in order for power to be delivered to the
Prototyping Board.
A
0
Cut traces
Bottom Side
JP1
JP2
JP1 (+5 V)
or
JP2 (+3.3 V)
CURRENT
MEASUREMENT
D1
R1
PWR
DS1
GND
J1
U1
C1
GND
C2
JP1
C3
D2
JP2
L1C6
C5
JP1
JP2
相關PDF資料
PDF描述
20-101-1197 MODULE RABBITCORE RCM3910 ROHS
20-101-1215 MCU RCM4050 RABBITCORE
20-101-1246 CORE MODULE RCM5400W
20-101-1260 BL5S220 SBC (RCM5400-BASED)
20-101-1319 MINCORE MODULE RCM6710
相關代理商/技術參數
參數描述
20-101-1170 功能描述:Zigbee/802.15.4模塊 RCM4510W CORE MODULE RoHS:否 制造商:Digi International 頻帶:902 MHz to 928 MHz 視線范圍: 數據速率: 靈敏度: 工作電源電壓:2.4 V to 3.6 V 傳輸供電電流:215 mA 接收供電電流:26 mA 輸出功率:250 mW 天線連接器類型:Wire 最大工作溫度:+ 85 C 尺寸:32.94 mm x 22 mm x 2.03 mm
20-101-1179 功能描述:模塊化系統 - SOM RCM3209 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1183 功能描述:程序設計器配件 USB PROGRAM CABLE RoHS:否 制造商:Lattice 產品:ispDOWNLOAD Cables 用于:In-system Programming
20-101-1184 功能描述:模塊化系統 - SOM IC CPU RABBIT 2000 (2 pack) RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1185 功能描述:微處理器 - MPU IC CPU RABBIT 3000A (2 pack) RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*