參數資料
型號： 20-101-1131
廠商： Rabbit Semiconductor
文件頁數： 44/134頁
文件大?。?/td> 0K
描述： MODULE RCM4200 RABBITCORE
產品培訓模塊： WiFi Authentication
標準包裝： 1
系列： RabbitCore®
模塊/板類型： MPU 核心模塊
適用于相關產品： RCM4200
其它名稱： 316-1124
User’s Manual
11
If you are using a USB programming cable, your PC should recognize the new USB hard-
ware, and the LEDs in the shrink-wrapped area of the programming cable will flash — if
you get an error message, you will have to install USB drivers. Drivers for Windows XP
are available in the Dynamic C Drivers\Rabbit USB Programming Cable\
WinXP_2K
folder — double-click DPInst.exe to install the USB drivers. Drivers for
other operating systems are available online at www.ftdichip.com/Drivers/VCP.htm.
2.2.4 Step 4 — Connect Power
Once all the other connections have been made, you can connect power to the Prototyping
Board.
If you have the universal AC adapter, prepare the AC adapter for the country where it will
be used by selecting the appropriate plug. Snap in the top of the plug assembly into the slot
at the top of the AC adapter as shown in Figure 4, then press down on the plug until it
clicks into place.
Connect the AC adapter to 3-pin header J1 on the Prototyping Board as shown in Figure 4
above. The connector may be attached either way as long as it is not offset to one side—
the center pin of J1 is always connected to the positive terminal, and either edge pin is
ground.
Plug in the AC adapter. The PWR LED on the Prototyping Board next to the power con-
nector at J1 should light up. The RCM4200 and the Prototyping Board are now ready to be
used.
NOTE: A RESET button is provided on the Prototyping Board next to the battery holder
to allow a hardware reset without disconnecting power.
To power down the Prototyping Board, unplug the power connector from J1. You should
disconnect power before making any circuit adjustments in the prototyping area, changing
any connections to the board, or removing the RCM4200 from the Prototyping Board.
相關PDF資料
PDF描述
20-101-1139 RCM4310 RABBITCORE
20-101-1154 MODULE RCM4120 RABBITCORE
20-101-1197 MODULE RABBITCORE RCM3910 ROHS
20-101-1215 MCU RCM4050 RABBITCORE
20-101-1246 CORE MODULE RCM5400W
相關代理商/技術參數
參數描述
20-101-1132 功能描述:模塊化系統 - SOM RCM4210 RabbitCore- Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1136 功能描述:射頻模塊 RF Module Interface RoHS:否 制造商:Linx Technologies 產品:Transceiver Modules 頻帶:902 MHz to 928 MHz 輸出功率:- 15.5 dBm to + 12.5 dBm 接口類型:UART 工作電源電壓:- 0.3 VDC to + 5.5 VDC 傳輸供電電流:38.1 mA 接收供電電流:22.7 mA 天線連接器類型:U.FL 最大工作溫度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm
20-101-1138 功能描述:模塊化系統 - SOM RCM4300 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1139 功能描述:模塊化系統 - SOM RCM4310 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1140 功能描述:WiFi/802.11模塊 RCM4400W CORE MODULE Wi-Fi/802.11 RoHS:否 制造商:Taiyo Yuden 支持協議:802.11 b/g/n 頻帶: 數據速率:150 Mbps 接口類型:SDIO 傳輸功率（最大）: 天線連接器類型: 工作電源電壓:3.4 V to 5.5 V 傳輸供電電流: 接收供電電流: 最大工作溫度:+ 80 C 尺寸:35 mm x 15 mm x 2.9 mm
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*