- 您現在的位置：買賣IC網 > PDF目錄368708 > 1374 (Linear Technology Corporation) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | 1374 |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 抗輻射高效，5安培開關穩壓器 |
| 文件頁數： | 26/32頁 |
| 文件大?。?/td> | 309K |
| 代理商： | 1374 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁
26
LT1374
1374fb
APPLICATIO
S I
FOR
ATIO
U
With the conditions above:
W
U
U
DC
=
+
.
+ +
5
=
5
0 3
0 5
.
5 5
.
0 5
.
51
%
This duty cycle is close enough to 50% that I
P
can be
assumed to be 4.5A.
OUTPUT DIVIDER
If the adjustable part is used, the resistor connected to
V
OUT
(R2) should be set to approximately 5k. R1 is
calculated from:
(
.
R
R V
OUT
2
1
–2 42
2 42
=
)
INDUCTOR VALUE
Unlike buck converters, positive-to-negative converters
cannot use large inductor values to reduce output ripple
voltage. At 500kHz, values larger than 25
μ
H make almost
no change in output ripple. The graph in Figure 16 shows
peak-to-peak output ripple voltage for a 5V to –5V con-
verter versus inductor value. The criteria for choosing the
inductor is therefore typically based on ensuring that peak
switch current rating is not exceeded. This gives the
lowest value of inductance that can be used, but in some
cases (lower output load currents) it may give a value that
creates unnecessarily high output ripple voltage. A com-
promise value is often chosen that reduces output ripple.
As you can see from the graph, largeinductors will not
give arbitrarily low ripple, but smallinductors can give
high ripple.
The difficulty in calculating the minimum inductor size
needed is that you must first know whether the switcher
will be in continuous or discontinuous mode at the critical
point where switch current is 4.5A. The first step is to use
the following formula to calculate the load current where
the switcher must use continuous mode. If your load
current is less than this, use the discontinuous mode
formula to calculate minimum inductor needed. If load
current is higher, use the continuous mode formula.
Output current where continuous mode is needed:
I
V
I
V
V
V
V
V
CONT
IN
)
IN
OUT
IN
OUT
F
=
( ) ( )
(
+
(
+
+
)
2
2
4
Minimum inductor discontinuous mode:
=
(
( )( )
L
V
I
f I
MIN
OUT
OUT
2
P
)(
)
2
Minimum inductor continuous mode:
L
V
V
f V
( )
V
I
I
V
V
V
MIN
IN
OUT
IN
OUT
P
OUT
OUT
F
IN
=
( )(
)
+
(
)
+
+
(
)
2
1
For the example above, with maximum load current of 1A:
I
A
CONT
=
(
+
) (
(
)
5
(
)
+ +
)
=
5.
4 5
.
4 5 5
5 5 5
0 5
.
1 15
.
2
2
.
.
Figure 16. Ripple Voltage on Positive-to-Negative Converter
INDUCTOR SIZE (
μ
H)
0
O
P
)
250
200
150
100
50
0
20
1374 F16
5
10
15
5V TO –5V CONVERTER
OUTPUT CAPACITOR’S
ESR = 0.05
I
LOAD
= 0.25A
I
LOAD
= 1A
相關PDF資料 |
PDF描述 |
|---|---|
| 13745 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 1374HV | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 1374HVI | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 1374I | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 1374I5 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1374-001-W | 制造商:MISCELLANEOUS 功能描述: |
| 1374018-2 | 制造商:TE Connectivity 功能描述: |
| 1374019-3 | 功能描述:光纖連接器 MTRJ JACK 62.5/125 PIGTAIL RoHS:否 制造商:Molex 產品:Adapters 類型:8 Port with External Shutter 連接器類型:Adapter 模式:Multimode 光纖直徑: 顏色:Blue 附件類型:LC Adapter |
| 1374020-1 | 功能描述:光纖連接器 MTRJ JACK SM PIGTAIL RoHS:否 制造商:Molex 產品:Adapters 類型:8 Port with External Shutter 連接器類型:Adapter 模式:Multimode 光纖直徑: 顏色:Blue 附件類型:LC Adapter |
| 1374047-1 | 制造商:TE CONNECTIVITY 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。