- 您現在的位置：買賣IC網 > PDF目錄1887 > 100-1225-1 (Bluetechnix)CORE MOD TCM-BF537 500MHZ CONN PDF資料下載
參數資料
| 型號： | 100-1225-1 |
| 廠商： | Bluetechnix |
| 文件頁數： | 17/35頁 |
| 文件大小： | 0K |
| 描述： | CORE MOD TCM-BF537 500MHZ CONN |
| 標準包裝： | 1 |
| 模塊/板類型： | 核心模塊 |
| 其它名稱： | 100-1221-1 100-1225 100-1225-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
DEV-BF5xxDA-lite V5.x Hardware User Manual
23
Due to the limited number of pins on the two connectors, the CM-BF561 can only set its boot mode on the core
module itself by changing the resistor settings. See the CM-BF561 manual for further details.
7
Using a Core Module with on board USB
If you use a Core Module with USB feature, for example the CM-BF527 set switch 4 of S2 to “on”. This connects the
5.0V pin of the USB connector X9 to pin 53 of the Core Module.
If you do not use a Core Module with on board USB feature the switch 4 of S2 should always remain “off”.
8
Installation
8.1
Initial Board Setup
The installation guide is written for Windows (Windows 2000 and WinXP). However for connecting the USB
device the drivers for MAC and LINUX are available on the CD.
In order to set up und test the board the follow the next steps:
1.
Make sure the Jumper JP1 and JP2 are set and the switch S4 is in position 0 as shown in Figure 8-1 .
Figure 8-1: Setup of the DEV-BF5xxDA-Lite Board
2.
Set switch S2 according chapter 5.2 and 6. Set switch S1 according chapter 5.1.
3.
Connect the power supply to the power connector of the DEV-BF5xxDA-Lite board.
4.
Connect the DEV-BF5xxDA-Lite Board via USB to the PC. The pre-flashed BLACKSheep starts and the LED
mounted on the EVAL board starts blinking. On the PC usually the ‘Found New Hardware Wizard’ opens.
相關PDF資料 |
PDF描述 |
|---|---|
| 100-1254-2 | MODULE BF527-C-C-Q50S64F8 |
| 101-0303 | SMARTSCREEN OP7100 DISPLAY |
| 101-0383 | MODULE RABBITCORE RCM2020 |
| 101-0435 | MODULE RABBITCORE RCM2110 |
| 101-0453 | MODULE RABBITCORE RCM2300 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 10-01-2259 | 功能描述:集管和線殼 KK 100 Housing Crimp Crimp Std 25 Ckt RoHS:否 產品種類:1.0MM Rectangular Connectors 產品類型:Headers - Pin Strip 系列:DF50 觸點類型:Pin (Male) 節距:1 mm 位置/觸點數量:16 排數:1 安裝風格:SMD/SMT 安裝角:Right 端接類型:Solder 外殼材料:Liquid Crystal Polymer (LCP) 觸點材料:Brass 觸點電鍍:Gold 制造商:Hirose Connector |
| 100122A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Nine Bit Buffer |
| 100122DC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Nine Bit Buffer |
| 100122DCQR | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| 100-122F | 功能描述:固定電感器 1.2uH 1% 1ohm SMT RF Inductor RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
發布緊急采購，3分鐘左右您將得到回復。