- 您現在的位置：買賣IC網 > PDF目錄23082 > 050-000-0030010 (ITT Corporation) RF Coaxial Connectors PDF資料下載
參數資料
| 型號： | 050-000-0030010 |
| 廠商： | ITT Corporation |
| 英文描述： | RF Coaxial Connectors |
| 中文描述： | 射頻同軸連接器 |
| 文件頁數： | 22/39頁 |
| 文件大?。?/td> | 471K |
| 代理商： | 050-000-0030010 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
Dimensions are shown in mm (inch)
Dimensions subject to change
133
Assy Insts
RF Coaxial Connectors
Assembly Instructions
BBAI-1119
SMZ Straight Connectors, Crimp Contact, for Braided Cable
Cable
Die Size
BT2001
4,52 (.178)
BT2002
5,18 (.204)
BT2003
6,81 (.268)
BT3002
4,52 (.178)
RG59B/U
6,48 (.255)
RG179B/U
3,25 (.128)
RG187A/U
3,25 (.128)
TZC75024
4,52 (.178)
FERRULE
REAR BODY ASSEMBLY
CONTACT
(REAR PORTION)
FRONT
INSULATOR
(PLUG ONLY)
1. Check that the center contact is a free fit in the front insulator and that you have all the connector
parts. The termination technique and cable preparation dimensions for the sockets are the same.
2. Strip the cable to the dimensions shown taking care not to damage the braid, dielectric or inner
conductor. Slip ferrule over cable.
3. Slide the connector body over the cable so that the rear body goes between the dielectric and the
braid. Gently twisting and rocking the connector body to spread the braid will help. Care must be
taken to ensure that no strands of braid are trapped under the body.
4. Slide the crimp ferrule forward over the braid until it butts up against the backnut. Crimp using
ITT Cannon crimp tool fitted with suitable die set (see table).
5. Trim the center conductor so that 3,50 (.138) protrudes from the face of the rear insulator. Position
the crimp type center pin over the end of the center conductor. The wire should be visible through
the inspection hole when positioned for crimping.
6. A separate crimping tool will be needed to crimp the center pin. A suitable tool being the
ITT Cannon crimp tool T4519.
7. The center pin together with the connector body is inserted into the locator of the crimp tool, taking
care that the center pin does not fall off in the process! As the connector body is inserted, the spring
loaded plunger positions the center pin against the rear insulator. With the connector firmly pushed
into the locator, crimp the center pin. (Ensure assembly is resting on bottom of locator.)
8. Withdraw the connector. Assemble the front and rear bodies. If a free fit front insulator is utilised
ensure that it is positioned the correct way round. Finally tighten the two body sections using
torque wrenches ITT Cannon part numbers T0854/M8/E and T0854/13/E, to a torque of 0,98 -
1,06 Nm (140 - 150 in. ozs.).
BRAID OPENED
FOR REAR BODY
相關PDF資料 |
PDF描述 |
|---|---|
| 09457150123 | INTERCONNECTION DEVICE |
| 09457150125 | INTERCONNECTION DEVICE |
| 09457150127 | INTERCONNECTION DEVICE |
| 09457151127 | INTERCONNECTION DEVICE |
| 09457151183 | INTERCONNECTION DEVICE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 050-000-0030020 | 制造商:ITT 制造商全稱:ITT Industries 功能描述:RF Coaxial Connectors |
| 050-000-0030040 | 制造商:ITT 制造商全稱:ITT Industries 功能描述:RF Coaxial Connectors |
| 050-000-0030070 | 制造商:ITT 制造商全稱:ITT Industries 功能描述:12-POINT CENTER PIN CRIMP TOOL |
| 050-000-010 | 制造商:ITW Pancon 功能描述:STRAIN RELIEF BRACKET 10POS POLYESTER 制造商:ITW Pancon 功能描述:10 CIRC LATCON STRAIN & RELIEF 制造商:ITW Pancon 功能描述:STRAIN RELIEF BRACKET, 10POS, POLYESTER; Series:LAT-CON; Accessory Type:Strain Relief Bracket; For Use With:Series 050 Sockets; No. of Positions:10; Strain Relief Material:-; No. of Contacts:10 ;RoHS Compliant: Yes 制造商:ITW Pancon 功能描述:Connector Accessories Strain Relief Bracket 制造商:PANCON CONNECTORS 功能描述:Connector Accessories Strain Relief Bracket |
| 050-000-0130000 | 制造商:ITT 制造商全稱:ITT Industries 功能描述:RF Coaxial Connectors |
發布緊急采購，3分鐘左右您將得到回復。