- 您現在的位置：買賣IC網 > PDF目錄22731 > 02-ATB-1200 RS232 INTERFACE PCB FOR PDF資料下載
參數資料
| 型號： | 02-ATB-1200 |
| 英文描述： | RS232 INTERFACE PCB FOR |
| 中文描述： | RS232接口電路板的 |
| 文件頁數： | 11/15頁 |
| 文件大小： | 1095K |
| 代理商： | 02-ATB-1200 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁
ATB1200 User Guide Page 5 of 15
3
EXTERNAL CONNECTIONS
The ATB1200 has three external connectors for Power Input (J1), Host Communication (J2) and for
connecting to the ELM205-ST mechanism (J3).
IMPORTANT NOTE:
A fourth connector (J4) is present on the PCB; see “Appendix 1 - ATB1200 Layout Diagram” on page
14. NO CONNECTION SHOULD BE MADE TO J4 AT ANY TIME. J4 is used during factory
programming of the firmware for the main controller IC. If connection is made to J4 during normal
use, the factory-fitted resident firmware may be corrupted or erased. In this case the ATB1200 must
be returned to ASL for re-programming. A charge will be made for this service.
N.B. An additional connector providing User Front Panel Connections to a Paper Feed Input and an
LED output will be provided. However, that this facility is not available on the Revision 8 ATB1200
PCB. See “Section 6 - User Feed Switch and LED” on page 11 for more details.
3.1
CONNECTOR DETAILS AND SUGGESTED MATING PART NUMBERS
Reference
Connector Fitted
Suggested Mating Part
J1
2-Way Power Input
Molex Part No: 26-60-4020
09-91-0200 (Molex Housing)
08-52-0072 (Molex Crimp)
J2
6-Way Data Input
Molex Part No: 22-27-2061
22-01-2065 (Molex Housing)
08-50-0032 (Molex Crimp)
J3
27-Way Mechanism Connection
Molex Part No: 52806-2710
FPC fitted on ELM205-ST
J4
2-Way Jumper Pins
Do Not Make Any Connection to J4
See “Figure 1 - ATB1200 Dimensional Diagram” on page 3, or “Appendix 1 - ATB1200 Layout
Diagram” on page 14, for orientation details.
3.2
J1 PINOUTS (POWER INPUT CONNECTOR)
The 2-way power connector has the following pinouts:
Pin
Assignment
Pin 1
Power Ground
Pin 2
Vmech (DC Power In)
3.3
POWER SUPPLY REQUIREMENT
The DC power should be supplied between +4.75V DC and +8.5V DC. For best printing use between
+ 5V DC and +7.5V DC. Never supply more than +8.5V DC.
Avoid voltage drops by taking care over wiring and connections. Do not interrupt, reverse or reduce
the voltage or damage will occur.
Average current during normal printing is normally around 2A. Peak current may be up to 10A. We
recommend a 3A power supply, although a higher specification may be necessary for some
applications.
See “Section 5.5 - Feeding and Printing Performance” on page 10 for more information on the trade-
offs that can be made between PSU voltage, PSU current capacity and printing performance.
相關PDF資料 |
PDF描述 |
|---|---|
| 05266.123.204 | 6 mm2, COPPER ALLOY, WIRE TERMINAL |
| 05266.123.211 | 6 mm2, COPPER ALLOY, WIRE TERMINAL |
| 05267.123.211 | 1 mm2, BRASS, TIN FINISH, WIRE TERMINAL |
| 05363.123.242 | 1 mm2, BRASS, SILVER FINISH, WIRE TERMINAL |
| 05562.123.211 | 1.5 mm2, BRASS, TIN FINISH, WIRE TERMINAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 02ATK303C | 制造商:Mitutoyo Corporation 功能描述:RING FIBER CABLE (L=7M) |
| 02ATK304D | 制造商:Mitutoyo Corporation 功能描述:QV PRL CABLE (L=4M) |
| 02ATK304F | 制造商:Mitutoyo Corporation 功能描述:QV PRL CABLE (L=5M) |
| 02ATK304H | 制造商:Mitutoyo Corporation 功能描述:QV PRL CABLE (L=6.5M) |
| 02ATK304P | 制造商:Mitutoyo Corporation 功能描述:QV PRL CABLE (L=5.5M) |
發布緊急采購，3分鐘左右您將得到回復。