- 您現在的位置：買賣IC網 > PDF目錄372903 > XE1414L Telecommunication IC PDF資料下載
參數資料
| 型號： | XE1414L |
| 英文描述： | Telecommunication IC |
| 中文描述： | 通信集成電路 |
| 文件頁數： | 11/17頁 |
| 文件大?。?/td> | 64K |
| 代理商： | XE1414L |
XECOM
(11)
XE1414B
XE1414B Modem Registers (continued)
S14
General Bit-Mapped Options:
S14
reflects the
state of several "AT" commands.
Bit 0,4,6
Not Used
Bit 1
0 = Echo Disabled (ATE0)
1 = Echo Active (ATE1)
Bit 2
0 = Send Result Codes (ATQ0)
1 = No Result Codes (ATQ1)
Bit 3
0 = Numeric Result Codes (ATV0)
1 = Full Word Result Codes (ATV1)
Bit 5
0 = Tone Dialing Selected (T)
1 = Pulse Dialing Selected (P)
Bit 7
0 = Answer
1 = Originate
S16
Test Status:
S16 shows the modem test status.
Bit 0
0 = No Local Analog Loopback
1 = Local ALB Active
Bit 1
Not Used
Bit 2
0 = Local Digital Loopback Disabled
1 = Local DLB Enabled
Bit 3
0 = No Remote Digital Loopback
1 = Remote DLB Active
Bit 4
0 = Remote DLB not requested
1 = Remote DLB Requested
Bit 5
0 = Remote DLB w Self-Test Disabled
1 = Remote DLB w Self-Test Enabled
Bit 6
0 = Local ALB w Self-Test Disabled
1 = Local ALB w Self-Test Enabled
Bit 7
Not Used
S18
Test Timer:
S18 sets the duration of any test. If S18
equals 0, AT&T0 terminates the test.
Range:
0 to 255
Units
Seconds
Default
0
S21
General Bit-Mapped Options:
S21 reflects the state
of several "AT" commands.
Bit 0-2
Not Used
Bit 3,4
0 = DTR ignored (&D0)
1 =
Enter command mode on DTR off
(&D1)
2 = Disconnect on DTR off (&D2)
3 = Reset on DTR off (&D3)
Bit 5
0 = DCD always active (&C0)
1 = DCD on with Carrier (&C1)
Bit 6
0 = DSR always active (&C0)
1= DSR on when modem ready (&C1)
Bit 7
0 = No disconnect on Space (ATY0)
1 = Disconnect on Space (ATY1)
S22
General
Bit-Mapped Options:
S22 reflects the state
of several "AT" commands.
Bit 0-1
0 = Low speaker volume (ATL0)
1 = Low speaker volume (ATL1)
2
= Moderate speaker volume (ATL2)
3 = High speaker volume (ATL3)
Bit 2-3 0 = Speaker off (ATM0)
1 = Speaker off with carrier (ATM1)
2 = Speaker always on (ATM2)
3 = Speaker on during handshake
(ATM3)
Bit 4-6 0 = Basic Result codes (ATX0)
4
= Connect speed result codes (ATX1)
5 = No Blind Dial (ATX2)
6 = Busy Detection (ATX3)
7 = Full result codes (ATX4)
Bit 7
Not Used
S23
General Bit-Mapped Options:
S23 reflects the state
of several "AT" commands.
Bit 0
0 = Remote DLB Disabled (AT&T5)
1 = Remote DLB Allowed (AT&T4)
Bit 1-3 0 = Host Interface at 300 bps
1 = Host Interface at 600 bps
2 = Host Interface at 1200 bps
3 = Host Interface at 2400 bps
4 = Host Interface at 4800 bps
5 = Host Interface at 9600 bps
6 = Host Interface at 19200 bps
7 = Host I/F at 38400 bps or higher
Bit 4-5 0 = Even parity in use
1 = Not used
2 = Odd Parity in use
3 = No Parity in use
Bit 6-7 0 = No Guard Tone (AT&G0)
1 = No Guard Tone (AT&G1)
2 = 1800 Hz guard tone (AT&G2)
3 = Not Used
相關PDF資料 |
PDF描述 |
|---|---|
| XE1414VP | Telecommunication IC |
| XE1414VS1 | Telecommunication IC |
| XE1414VS2 | Telecommunication IC |
| XE1414VTS1 | Telecommunication IC |
| XE1414M | Telecommunication IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XE1414M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XE1414P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XE1414V | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XE1414VP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| XE1414VS1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
發布緊急采購，3分鐘左右您將得到回復。