- 您現在的位置：買賣IC網 > PDF目錄381152 > UC2886D Bluetooth® class 1 module with embedded HCI FW PDF資料下載
參數資料
| 型號： | UC2886D |
| 英文描述： | Bluetooth® class 1 module with embedded HCI FW |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 196K |
| 代理商： | UC2886D |
5
UC2886
UC3886
OSCILLATOR
The UC3886 oscillator is a saw tooth. The rising edge
is governed by a current controlled by RT flowing into
the capacitor CT. The falling edge of the sawtooth sets
the dead time for the output. Selection of RT should be
done first, based on desired maximum duty cycle. CT
can then be chosen based on the desired frequency,
F
S
, and the value of RT. The design equations are:
V
RT
mA
4 0
.
(
(
F
CT
V
RT
1 8
.
D
MAX
=
1
2 0
.
–
)
4 0
.
)
V
mA RT
V
mA
OSC
=
2 0
.
4 0
.
2
–2 0
Configuring the Current Sense Amplifier
The UC3886 Current Sense Amplifier is used to amplify
a differential current sense signal across a low value
current sense resistor, R
SENSE.
This amplifier must be
set up as a differential amplifier as shown.
The Current Sense Amplifier gain, G
CSA
, is given by the
ratio of R2/R1. The output of the Current Sense Ampli-
fier at the ISO pin is given by
R
R
V
V
V
ISO
BUF
SENSE
=
+
2
1
The Current Sense Amplifier gain, G
CSA
, must be pro-
grammed to be greater than or equal to 5.0 (14dB), as
this amplifier is not stable with gain below 5.0. The Cur-
rent Sense Amplifier gain is limited on the high side by
its Gain-Bandwidth product of 2.5MHz. Therefore G
CSA
must be programmed between
G
CSA_MIN
= 5.0 and
G
CSA_MAX
= 2.5MHz/F
SWITCH
APPLICATION INFORMATION
Figure 1. Oscillator
UDG-96022
0.88
0.90
0.92
0.94
0.96
0.98
1.00
0
20
40
60
80
100
120
R
T
(k
)
D
Figure 2. Programming Maximum Duty Cycle with R
T
10
100
1000
0
20
40
60
80
100
RT (k
)
F
100pF
220pF
470pF
1nF
Figure 3. Programming Switching Frequency with C
T
0.000
0.100
0.200
0.300
0.400
0.500
0.600
100
300
500
CT (pF)
700
900
1100
T
RT = 5k
RT = 100k
Figure 4. Deadtime vs. C
T
and R
T
相關PDF資料 |
PDF描述 |
|---|---|
| UC3886D | Quad exclusive OR gate |
| UC2901DW | Integrated Pots Interface for Home Access Gateway and WLL |
| UC1901L | 4 x 50W multifunction quad power amplifier with built-in diagnostics feature |
| UC1908T | VERY LOW DROP VOLTAGE REGULATOR |
| UC1908TD | Positive Adjustable Voltage Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UC2886DG4 | 功能描述:電流型 PWM 控制器 Avg Current Mode IC RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| UC28TRXS | 制造商:ST MICRO 功能描述:New |
| UC2901 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Isolated Feedback Generator |
| UC2901D | 功能描述:反饋回路功率控制器 Isolated Feedback Generator RoHS:否 參考電壓:1.3 V 輸出電流:100 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 封裝 / 箱體:SOIC-8 封裝:Tube 制造商:Texas Instruments |
| UC2901DG4 | 功能描述:反饋回路功率控制器 Isolated Feedback Generator RoHS:否 參考電壓:1.3 V 輸出電流:100 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 封裝 / 箱體:SOIC-8 封裝:Tube 制造商:Texas Instruments |
發布緊急采購，3分鐘左右您將得到回復。