- 您現在的位置：買賣IC網 > PDF目錄68698 > TRU050TKLGB35.328 (VECTRON INTERNATIONAL) PHASE LOCKED LOOP, CDIP16 PDF資料下載
參數資料
| 型號： | TRU050TKLGB35.328 |
| 廠商： | VECTRON INTERNATIONAL |
| 元件分類： | PLL合成/DDS/VCOs |
| 英文描述： | PHASE LOCKED LOOP, CDIP16 |
| 封裝： | ROHS COMPLIANT, HERMETIC SEALED, CERAMIC, DIP-16 |
| 文件頁數： | 12/14頁 |
| 文件大?。?/td> | 0K |
| 代理商： | TRU050TKLGB35.328 |
TRU050, VCXO Based PLL
Vectron International, 267 Lowell Rd, Hudson NH 03051-4916
Tel: 1-88-VECTRON-1
Web: www.vectron.com
Page 7 of 14
Rev : 06Jan2006
Loop Filter
A PLL is a feedback system which forces the output frequency to lock in both phase and frequency to the
input frequency. While there will be some phase error, theory states there is no frequency error. The loop
filter design will dictate many key parameters such as jitter reduction, stability, lock range and acquisition
time. Be advised that many textbook equations describing loop dynamics, such as capture range or lockin
time, are based on ideal systems. Such equations may not be accurate for real systems due to
nonlinearities, DC offsets, noise and don’t take into account the limited VCXO bandwidth. This section
deals with some real world design examples. Also, there is loop filter software on the Vectron web site,
plus experienced applications engineers are eager to assist in this process. Common TRU050 PLL
applications are shown in figures 7 and 8 (frequency translation), 9 (clock recovery) and 10 (clock
smoothing).
Of primary concern to the designer is selecting a loop filter that insures lock-in, stability and provides
adequete filtering of the input signal. A good starting point for the the loop filter bandwidth is 100ppm
times the DATAIN frequency. An example would be translating an 8kHz signal to 44. 736MHz – DS3 –
which is = 100 ppm x kHz = 8Hz . So for 8kHz inputs, ~ 8 Hz loop bandwidth may be reasonable and
figures 7 and 8 show and 8kHz to DS3 and 8kHz to 19.440 MHz frequency translation designs.
It’s fairly easy to set a low loop bandwidth for large frequency translations such as 8kHz to 44.736MHz,
but becomes more difficult for clock smoothing applications such as 19.440MHz in and 19.440MHz
output. In this example, 100ppm x 19.440MHz is about 2kHz and may be too high to reject kow frequency
jitter. A good way to resolve this is to lower the input frequency such as dividing the input frequency
down. The loop filter bandwidth becomes lower since 100ppm * DATAIN is lowered. Figure 10 shows an
example of how to design a low loop bandwith on a relatively high input signal and still maintain a wide
lock range. The “100ppm * DATAIN frequency” loop filter bandwidth can then be tailored to the
application, since lower bandwidthds are desriable to clean up and or translate clock signals and higher
bandwidths may be needed for clock recovery of NRZ signals.
There is no known accurate formula for calculating acquisition time and so the best way to provide
realisitc figures is to measure the lock time for a TRU050. Aquistion time was measured to be 3 to 5
seconds by measuring the control voltage in an 8kHz to 34.368 MHz frequency translation application -
similar to the application in figure 7 and 8, to sub 10 milliseconds for NRZ data patterns such as figure 9.
It may be tempting reduce the damping factor to 0.7 or 1.0 in order to increase aquisition time; but, it
degrades stability and will not signifigantly decrease lock time. This is due to the fact that most VCXO’s
have a 10kHz bandwidth so setting a 100kHz loop bandwidth is impossible. A damping factor of 4 is fairly
conservative and allows for excellent stability.
Some general quidelines for selecting loop filter include: Values should be less than 1Megohm and at
least 10Kohm between the PHO and OPN, the capacitor should be low leakage and a polarized capacitor
is acceptable, the R/C’s should be located physically close to the TRU050 . Also, the loop filter software
available on the web site was written for 5 volt operation, a simple way to calculate values for 3.3 volt
operation is to times the data density by 0.66 (3.3V / 5V).
SPICE models are another design aid. In most cases a new PLL TRU050 design is calculated by using
the software and verified with SPICE models, and depending on the circumstances evaluated in the
applications lab. The simple active pi model is in figure 7. Loop filter values can be modified to suit the
system requirements and application. There are many excellent references on designing PLL’s, such as
“Phase-Locked Loops, Theory, Design and Applications”, by Roland E Best McGraw-Hill; however, there
is loop filter software on the Vectron web site, plus experienced applications engineers eager to assist in
this process.
相關PDF資料 |
PDF描述 |
|---|---|
| TRU050TKLNA22.579 | PHASE LOCKED LOOP, CDIP16 |
| TRU050TKLNA32 | PHASE LOCKED LOOP, CDIP16 |
| TRU050TKLNA41.2416 | PHASE LOCKED LOOP, CDIP16 |
| TRU050TKLNB34.368 | PHASE LOCKED LOOP, CDIP16 |
| TRU050GACGB44.736 | PHASE LOCKED LOOP, CDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TRU050-TKLGB-65M0000000 | 制造商:VECTRON 制造商全稱:Vectron International, Inc 功能描述:Complete VCXO based Phase-Locked Loop |
| TRU050-TKLHA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE DROP IN QUARTZ STABILIZED PLL SOLUTUION |
| TRU050-TKLHA-1M0000000 | 制造商:VECTRON 制造商全稱:Vectron International, Inc 功能描述:Complete VCXO based Phase-Locked Loop |
| TRU050-TKLHA-65M0000000 | 制造商:VECTRON 制造商全稱:Vectron International, Inc 功能描述:Complete VCXO based Phase-Locked Loop |
| TRU050-TKLHB-1M0000000 | 制造商:VECTRON 制造商全稱:Vectron International, Inc 功能描述:Complete VCXO based Phase-Locked Loop |
發布緊急采購，3分鐘左右您將得到回復。