- 您現在的位置：買賣IC網 > PDF目錄69514 > TPS61006DGSRG4 (TEXAS INSTRUMENTS INC) 1.3 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO10 PDF資料下載
參數資料
| 型號： | TPS61006DGSRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.3 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | GREEN, PLASTIC, MSOP-10 |
| 文件頁數： | 21/25頁 |
| 文件大小： | 456K |
| 代理商： | TPS61006DGSRG4 |
TPS61000, TPS61001, TPS61002, TPS61003, TPS61004, TPS61005, TPS61006, TPS61007
SINGLE- AND DUAL-CELL BOOST CONVERTER WITH START-UP INTO FULL LOAD
SLVS279C – MARCH 2000 – REVISED APRIL 2003
5
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
detailed description (continued)
under-voltage lockout
An under-voltage lockout function prevents the device start-up if the supply voltage on VBAT is lower than
approximately 0.7 V. This undervoltage lockout function is implemented in order to prevent the malfunctioning
of the converter. When in operation and the battery is being discharged, the device automatically enters the
shutdown mode if the voltage on VBAT drops below approximately 0.7 V.
If the EN pin is hardwired to VBAT and if the voltage at VBAT drops temporarily below the UVLO threshold voltage,
the device switches off and does not start up again automatically, even if the supply voltage rises above 0.9 V.
The device starts up again only after a signal change from low to high on EN or if the battery voltage is completely
removed.
low Battery detector circuit (LBI and LBO)
The low-battery detector circuit is typically used to supervise the battery voltage and to generate an error flag
when the battery voltage drops below a user-set threshold voltage. The function is active only when the device
is enabled. When the device is disabled, the LBO pin is high impedance. The LBO pin goes active low when
the voltage on the LBI pin decreases below the set threshold voltage of 500 mV
±15 mV, which is equal to the
internal reference voltage. The battery voltage, at which the detection circuit switches, can be programmed with
a resistive divider connected to the LBI pin. The resistive divider scales down the battery voltage to a voltage
level of 500 mV, which is then compared to the LBI threshold voltage. The LBI pin has a built-in hysteresis of
10 mV. See the application section for more details about the programming of the LBI threshold.
If the low-battery detection circuit is not used, the LBI pin should be connected to GND (or to VBAT) and the LBO
pin can be left unconnected. Do not let the LBI pin float.
low-EMI switch
The device integrates a circuit which removes the ringing that typically appears on the SW-node when the con-
verter enters the discontinuous current mode. In this case, the current through the inductor ramps to zero and
the Schottky diode stops conducting. Due to remaining energy that is stored in parasitic components of the
diode, inductor, and switch, a ringing on the SW pin is induced. The integrated antiringing switch clamps this
voltage internally to VBAT and therefore dampens this ringing.
The antiringing switch is turned on by a comparator that monitors the voltage between SW and VOUT. This
voltage indicates when the diode is reverse biased. The ringing on the SW-node is damped to a large degree,
reducing the electromagnetic interference generated by the switching regulator to a very great extent.
adjustable output voltage (TPS61000 and TPS61007 only)
The accuracy of the internal voltage reference, the controller topology, and the accuracy of the external resistor
divider determine the accuracy of the adjustable output voltage versions. The reference voltage has an
accuracy of
±4% over line, load, and temperature. The controller switches between fixed frequency and
pulse-skip mode, depending on load current. This adds an offset to the output voltage that is equivalent to 1%
of VO. Using 1% accurate resistors for the feedback divider, a total accuracy of ±6% can be achieved over the
complete temperature and output current range. The TPS61007 is an improved adjustable output voltage
version. Ground shift in the feedback loop was eliminated by adding a separate ground pin for the feedback
resistor divider (FBGND).
相關PDF資料 |
PDF描述 |
|---|---|
| TPS61004DGSR | 1.3 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61007DGS | 1.3 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61006DGSR | 1.3 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61005DGSR | 1.3 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS61001DGS | 1.3 A SWITCHING REGULATOR, 840 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS61006DGST | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SINGLE- AND DUAL-CELL BOOST CONVERTER WITH START-UP INTO FULL LOAD |
| TPS61006DSGR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| TPS61006EVM-156 | 功能描述:電源管理IC開發工具 Low Input Vltg Boost Conv RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS61007 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SINGLE- AND DUAL-CELL BOOST CONVERTER WITH START-UP INTO FULL LOAD |
| TPS61007DGS | 功能描述:直流/直流開關調節器 Adj. 100mA Boost RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。