- 您現在的位置：買賣IC網 > PDF目錄69498 > TPIC43T01DA (TEXAS INSTRUMENTS INC) BRUSHLESS DC MOTOR CONTROLLER, PDSO38 PDF資料下載
參數資料
| 型號： | TPIC43T01DA |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PDSO38 |
| 封裝： | PLASTIC, TSSOP-38 |
| 文件頁數： | 4/29頁 |
| 文件大?。?/td> | 463K |
| 代理商： | TPIC43T01DA |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
TPIC43T01, TPIC43T02
THREE-PHASE BRUSHLESS MOTOR RPM CONTROLLERS
SLIS098 – APRIL 2000
12
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
lock timer oscillator/counter
Overall lock timer functionality is implemented by the combination of the oscillator and counter. The lock timer
oscillator is identical to the sampling frequency oscillator. The external resistor (RT) is used as the current
setting reference for both blocks. An external capacitor must be connected from the CLT terminal to GND to
set the period, T(CLT), of the lock timer oscillator. The nominal period is determined by the formula:
TCLT = 2 × RT × CLT. When an out-of-lock signal is generated by the lock detect block (see lock detect section),
the lock timer counter will count at the frequency of the lock timer oscillator. Should the out-of-lock signal remain
for the duration of the counter completing 1023 counts, a lock timer time-out signal will then be generated which
the shutdown logic block will respond to (see shutdown section). The lock timer time-out is thus set by
TCLT × 1023.
power-up clear
An under-voltage lockout and power-up clear are provided to ensure FET drive outputs are set to a known state
during power-up. The device is held in a CLEAR state until the following three conditions are met:
1.
VDD > VDD(uvlo), after which a power-up clear (PUC) time will begin.
2.
The PUC timer counts 3 cycles of internal 20 kHz signal (internal 5.8 MHz
÷ 255), or 132 s.
3.
The charge pump voltage, V(CP), has charged to at least VCC + 5 V.
shutdown
The scheme for shutdown includes monitoring two conditions and latching the device in a CLEAR state should
an abnormal condition occur. Once shutdown is latched, the S/S input must be cycled high then low, or power
cycled OFF then ON to release shutdown and resume normal operation. If an abnormal condition still exists after
the S/S pin has been cycled, the device will relatch shutdown. A 1 on either S/S or VDD pins will clear the lock
timer. A VDD under-voltage-lockout detect will force a global clear. (see Table 2 and Figure 6).
Table 2. Shutdown Conditions
LATCHED SHUTDOWN
CONDITIONS
UNLATCHED SHUTDOWN CONDITIONS
S/S
INTERNAL
CLR
LT
LTCLR
GATE
OUTPUTS
OCSD
LT
CP UV
VDD UVLO
INPUT
CLR
LTCLR
OUTPUTS
X
H
0
X
VDD < VDD(uvlo)
X
0
V(SENSE) < V(OCSD)
Out of
Lock < t(LT)
VO(CP) > V(CPUV)
VDD>VDD(uvlo)+3counts
H
↓L
1
X
VCP < V(CPUV)
for > t(DG)
X
0
V(SENSE) > V(OCSD)
for > t(DG)
X
0
X
Out of
Lock > t(LT)
X
L
X
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| TPIC74100QPWPRQ1 | 2.5 A SWITCHING REGULATOR, 440 kHz SWITCHING FREQ-MAX, PDSO20 |
| TPL9201PWP | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| TPPM0115DR | 0.5 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPPM0115D | 0.5 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO8 |
| TPS2010APWP | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPIC43T01DAR | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase Brushless Motor RPM Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TPIC43T02 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:THREE-PHASE BRUSHLESS MOTOR RPM CONTROLLERS |
| TPIC43T02DA | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase Brushless Motor RPM Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TPIC43T02DAR | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase Brushless Motor RPM Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TPIC44H01 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:4-CHANNEL SERIAL AND PARALLEL HIGH-SIDE PRE-FET DRIVER |
發布緊急采購，3分鐘左右您將得到回復。