- 您現在的位置：買賣IC網 > PDF目錄69498 > TPD4103K BRUSHLESS DC MOTOR CONTROLLER, 2 A, ZFM18 PDF資料下載
參數資料
| 型號： | TPD4103K |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 2 A, ZFM18 |
| 封裝： | HZIP-18 |
| 文件頁數： | 2/25頁 |
| 文件大?。?/td> | 222K |
| 代理商： | TPD4103K |
TPD4103K
2004-02-23
10
External Parts
Standard external parts are shown in the following table.
Part
Recommended Value
Purpose
Remarks
C1, C2, C3
25 V/2.2
F
Bootstrap capacitor
(Note 1)
R1
0.62
± 1% (1 W)
Current detection
(Note 2)
C4
25 V/10
F
VCC power supply stability
(Note 3)
CT
25 V/0.1
F
VCC for surge absorber
(Note 3)
C6
16 V/1
F
VREG power supply stability
(Note 3)
C7
16 V/1000 pF
VREG for surge absorber
(Note 3)
R3
5.1 k
DIAG pin pull-up resistor
(Note 4)
Note 1: The required bootstrap capacitance value varies according to the motor drive conditions. The capacitor is
biased by VCC and must be sufficiently derated for it.
Note 2: The following formula shows the detection current: IO = VR ÷ RIS (For VR = 0.5 V )
Do not exceed a detection current of 1 A when using this product.
Note 3: When using this product, some adjustment is required in accordance with the use environment. When
mounting, place as close to the base of this product leads as possible to improve the ripple and noise
elimination.
Note 4: The DIAG pin is open drain. Note that when the DIAG pin is connected to a power supply with a voltage
higher than or equal to the VCC, a protection circuit is triggered so that the current flows continuously. If not
using the DIAG pin, connect to the GND.
Handling precautions
(1)
Please control the input signal in the state to which the V CC voltage is steady. Both of the order of the
VBB power supply and the V CC power supply are not cared about either.
Note that if the power supply is switched off as described above, this product may be destroyed if the
current regeneration route to the VBB power supply is blocked when the VBB line is disconnected by
a relay or similar while the motor is still running.
(2)
The IS pin connecting the current detection resistor is connected to a comparator in this product and
also functions as a sensor pin for detecting over current. As a result, over voltage caused by a surge
voltage, for example, may destroy the circuit. Accordingly, be careful of handling this product or of
surge voltage in its application environment.
相關PDF資料 |
PDF描述 |
|---|---|
| TPD4111KLBR | BRUSHLESS DC MOTOR CONTROLLER, 2 A, PZFM23 |
| TPD4111KLB2 | BRUSHLESS DC MOTOR CONTROLLER, 2 A, PZFM23 |
| TPD4113AKLBF | BRUSHLESS DC MOTOR CONTROLLER, 2 A, PZFM23 |
| TPD4122K | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDIP26 |
| TPD4124K | BRUSHLESS DC MOTOR CONTROLLER, 3 A, PDIP26 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPD4104AK | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:TOSHIBA Intelligent Power Device High Voltage Monolithic Silicon Power IC |
| TPD4104AK(LB2,Q) | 功能描述:馬達/運動/點火控制器和驅動器 Intelligent Power Module RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TPD4104AK(LB2Q) | 制造商:Toshiba America Electronic Components 功能描述:IC DRIVER MOTOR 500V 2A 4104 |
| TPD4104AK_07 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:TOSHIBA Intelligent Power Device High Voltage Monolithic Silicon Power IC |
| TPD4104K | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:DC brush less motor driver using high voltage PWM control |
發布緊急采購，3分鐘左右您將得到回復。