- 您現在的位置：買賣IC網 > PDF目錄69498 > TPD4008KLBR BRUSHLESS DC MOTOR CONTROLLER, PZFM23 PDF資料下載
參數資料
| 型號： | TPD4008KLBR |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PZFM23 |
| 封裝： | 1.27 MM PITCH, PLASTIC, HZIP-23 |
| 文件頁數： | 3/24頁 |
| 文件大?。?/td> | 510K |
| 代理商： | TPD4008KLBR |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
TPD4008K
2001-05-31
11
Description of Bootstrap Capacitor Charging
The IC uses bootstrapping for the power supply for high-side drivers.
The bootstrap capacitor is charged by turning on the low-side IGBT of the same arm (approximately 1/5 of PWM
cycle) while the high-side IGBT controlled by PWM is off.
When the VS voltage exceeds 3.8 V (duty 55%), the low-side IGBT is continuously in the off state. This is because
when the PWM on-duty becomes larger, the arm is short-circuited while the low-side IGBT is on. Even in this state,
because PWM control is being performed on the high-side IGBT, the regenerative current of the diode flows to the
low-side FRD of the same arm, and bootstrap capacitor is charged. Note that when the on-duty is 100%, diode
regenerative current does not flow; thus, the bootstrap capacitor is not charged.
To determine the capacitance of the bootstrap capacitor, take the voltage drop at 100% duty into consideration.
(For example, to drive at 20 kHz, it takes approximately 10 s per cycle to charge the capacitor.)
VS Range
IGBT Operation
A
Both high- and low-side off.
B
Charging range.
Low-side IGBT turns on at the phase when the high-side IGBT turns on in the timing
chart.
C
No charging range.
High-side at PWM; low-side continues on according to the timing chart.
Safe Operating Area
*: The above safe operating area is Tc
= 95°C. If the temperature exceeds this, the safe operation area reduces.
*: The above safe operating area includes the overcurrent protection operation area. If the overcurrent protection
operation continues, depending on the heat discharge conditions, an overheating protection operation may result.
0.9
0
165
P
eak
w
indi
ng
c
u
rrent
(A
)
Power supply voltage
VBB (V)
0
Low-side ON
Duty 80%
C
Triangular wave
Duty 100% (VS: 5.4 V)
High-side duty ON
PWM reference voltage
Duty 55% (VS: 3.8 V)
Duty 0% (VS: 2.1 V)
VVsOFF (VS: 1.3 V)
GND
B
A
相關PDF資料 |
PDF描述 |
|---|---|
| TPD4008KLBF | BRUSHLESS DC MOTOR CONTROLLER, PZFM23 |
| TPD4011KLBF | BRUSHLESS DC MOTOR CONTROLLER, PZFM23 |
| TPD4103KLB2 | BRUSHLESS DC MOTOR CONTROLLER, 2 A, PZFM23 |
| TPD4103K | BRUSHLESS DC MOTOR CONTROLLER, 2 A, ZFM18 |
| TPD4111KLBR | BRUSHLESS DC MOTOR CONTROLLER, 2 A, PZFM23 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPD4011K | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MOTOR CONTROLLER |
| TPD4102K | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:TOSHIBA Intelligent Power Device High Voltage Monolithic Silicon Power IC |
| TPD4103AK(LBF) | 制造商:Toshiba America Electronic Components 功能描述: |
| TPD4104AK | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:TOSHIBA Intelligent Power Device High Voltage Monolithic Silicon Power IC |
| TPD4104AK(LB2,Q) | 功能描述:馬達/運動/點火控制器和驅動器 Intelligent Power Module RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。