- 您現在的位置：買賣IC網 > PDF目錄98203 > TDA8775G (NXP SEMICONDUCTORS) PARALLEL, WORD INPUT LOADING, 0.003 us SETTLING TIME, 10-BIT DAC, PQFP48 PDF資料下載
參數資料
| 型號： | TDA8775G |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | DAC |
| 英文描述： | PARALLEL, WORD INPUT LOADING, 0.003 us SETTLING TIME, 10-BIT DAC, PQFP48 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, SOT-313-2, LQFP-48 |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 95K |
| 代理商： | TDA8775G |
2002 Apr 24
14
Philips Semiconductors
Product specication
Triple 10-bit video Digital-to-Analog
Converter (DAC)
TDA8775
SOLDERING
Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
“Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is
recommended.
Reow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
Typical reflow peak temperatures range from
215 to 250
°C. The top-surface temperature of the
packages should preferable be kept below 220
°C for
thick/large packages, and below 235
°C for small/thin
packages.
Wave soldering
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is preferred to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
For packages with leads on four sides, the footprint must
be placed at a 45
° angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°C.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8776AK-T | PARALLEL, WORD INPUT LOADING, 0.002 us SETTLING TIME, 10-BIT DAC, PQCC28 |
| TDA8776AK | PARALLEL, WORD INPUT LOADING, 0.002 us SETTLING TIME, 10-BIT DAC, PQCC28 |
| TDA8776K-T | PARALLEL, WORD INPUT LOADING, 0.002 us SETTLING TIME, 10-BIT DAC, PQCC28 |
| TDA8776K | PARALLEL, WORD INPUT LOADING, 0.002 us SETTLING TIME, 10-BIT DAC, PQCC28 |
| TDA8777HL/14 | PARALLEL, WORD INPUT LOADING, 10-BIT DAC, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8775G/C1,151 | 功能描述:數模轉換器- DAC TRIPLE 10-BIT VIDEO DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| TDA8775GB-S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video DAC without Color Palette |
| TDA8775GB-T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video DAC without Color Palette |
| TDA8776 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:10-bit, 500 Msps Digital-to-Analog Converter DAC |
| TDA8776A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:10-bit, 1000 Msps Digital-to-Analog Converter DAC |
發布緊急采購，3分鐘左右您將得到回復。