參數資料
型號: STM32F103R8T7TR
廠商: STMICROELECTRONICS
元件分類: 微控制器/微處理器
英文描述: 32-BIT, FLASH, 1.25 MHz, RISC MICROCONTROLLER, PQFP64
封裝: 10 X 10 MM, ROHS COMPLIANT, QFP-64
文件頁數: 5/92頁
文件大小: 1212K
代理商: STM32F103R8T7TR
STM32F103x8, STM32F103xB
Description
Doc ID 13587 Rev 11
This hardware block provides flexible interrupt management features with minimal interrupt
latency.
2.3.6
External interrupt/event controller (EXTI)
The external interrupt/event controller consists of 19 edge detector lines used to generate
interrupt/event requests. Each line can be independently configured to select the trigger
event (rising edge, falling edge, both) and can be masked independently. A pending register
maintains the status of the interrupt requests. The EXTI can detect an external line with a
pulse width shorter than the Internal APB2 clock period. Up to 80 GPIOs can be connected
to the 16 external interrupt lines.
2.3.7
Clocks and startup
System clock selection is performed on startup, however the internal RC 8 MHz oscillator is
selected as default CPU clock on reset. An external 4-16 MHz clock can be selected, in
which case it is monitored for failure. If failure is detected, the system automatically switches
back to the internal RC oscillator. A software interrupt is generated if enabled. Similarly, full
interrupt management of the PLL clock entry is available when necessary (for example on
failure of an indirectly used external crystal, resonator or oscillator).
Several prescalers allow the configuration of the AHB frequency, the high-speed APB
(APB2) and the low-speed APB (APB1) domains. The maximum frequency of the AHB and
the high-speed APB domains is 72 MHz. The maximum allowed frequency of the low-speed
APB domain is 36 MHz. See Figure 2 for details on the clock tree.
2.3.8
Boot modes
At startup, boot pins are used to select one of three boot options:
Boot from User Flash
Boot from System Memory
Boot from embedded SRAM
The boot loader is located in System Memory. It is used to reprogram the Flash memory by
using USART1. For further details please refer to AN2606.
2.3.9
Power supply schemes
VDD = 2.0 to 3.6 V: external power supply for I/Os and the internal regulator.
Provided externally through VDD pins.
VSSA, VDDA = 2.0 to 3.6 V: external analog power supplies for ADC, reset blocks, RCs
and PLL (minimum voltage to be applied to VDDA is 2.4 V when the ADC is used).
VDDA and VSSA must be connected to VDD and VSS, respectively.
VBAT = 1.8 to 3.6 V: power supply for RTC, external clock 32 kHz oscillator and backup
registers (through power switch) when VDD is not present.
For more details on how to connect power pins, refer to Figure 12: Power supply scheme.
2.3.10
Power supply supervisor
The device has an integrated power-on reset (POR)/power-down reset (PDR) circuitry. It is
always active, and ensures proper operation starting from/down to 2 V. The device remains
相關PDF資料
PDF描述
STM32W108HBU7 SPECIALTY MICROPROCESSOR CIRCUIT, QCC40
STP506C-2IW-012V SINGLE COLOR DISPLAY CLUSTER, WHITE, 152.4 mm
SUGR47M DUAL COLOR LED, RED/GREEN, 5 mm
SUR76D SINGLE COLOR LED, RED, 3 mm
SUY17D SINGLE COLOR LED, YELLOW, 3.9 mm
相關代理商/技術參數
參數描述
STM32F103R8T7XXX 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Medium-density performance line ARM-based 32-bit MCU with 64 or 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 communication interfaces
STM32F103R8U6TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Medium-density performance line ARM-based 32-bit MCU with 64 or 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 communication interfaces
STM32F103R8U6XXX 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Medium-density performance line ARM-based 32-bit MCU with 64 or 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 communication interfaces
STM32F103R8U7TR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Medium-density performance line ARM-based 32-bit MCU with 64 or 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 communication interfaces
STM32F103R8U7XXX 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Medium-density performance line ARM-based 32-bit MCU with 64 or 128 KB Flash, USB, CAN, 7 timers, 2 ADCs, 9 communication interfaces