- 您現在的位置：買賣IC網 > PDF目錄380765 > STLC5412P (意法半導體) 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE PDF資料下載
參數資料
| 型號： | STLC5412P |
| 廠商： | 意法半導體 |
| 英文描述： | 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE |
| 中文描述： | 2B1Q U接口裝置加強與無繩模式 |
| 文件頁數： | 9/74頁 |
| 文件大?。?/td> | 655K |
| 代理商： | STLC5412P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
PIN FUNCTIONS
(specificGCI mode)
Pin
22
Name
RFS
In/Out
In
Description
Remote febe select:
When tied to 0 the remote febe is not transferred. When tied to 1febe is
transparently reported. See figure 10.
TxSuper framesynchronization. In LTmode thispin is aninput giving the Tx
SuperFrame Synchronization if SFS= 0 in CR2.It becomes an output if SFS
= 1 withISW free running on the line. In NT mode this pinis always an output
giving the TxSuperFrame position. If DECTmode is selected (DECT = 1in
CR7) thispin provide the DECT synchronization pulse at eachvalidated
reception of the DECT eoc message.
Analog interface selectfor all auto mode configurations
Rx Super frame synchronization. The rising edge of SFSr indicates the
beginning of the received superframe on the line. UID provides this output
only when ESFR bit in CR4 register is to 1 and LT/NT12 or NT/TE
configuration is done.
Line Signal Detect output (default configuration): This pin is an open drain
output which is normally in the high impedance state but pulls low when the
device previously in the power down state receives a wake-up by Tone from
the line. This signal is intended to be usedto wake-up a micro-controller
from a low power idle mode. The LSD output goes back in the high
impedance state when the device is powered up.
Reset input pin with internal pull-up resistor. When pulled low, all registers
of the UID are reset to their default values. UID is configured according to
configuration inputs bias excluding MW input which must be maintained at
the 0 volt. minimum recommended pulse length is 200
μ
s.
Configuration input pin. When pulled low,GCI channel assigneris selected
(channel number defined by inputs S0, S1, S2). When pulled high, UID is
configured by pins CONF1 and CONF2.
SFSx
In Out
25
AIS
SFSr
In
Out
LSD
Out
26
RES
In
27
M0
In
MULTIPLE FUNCTION PIN DESCRIPTION
Pin 6:
FSa
Function or In/Out conditions
Function
FSa
FSa
FSa
FSa
FSa
FSa
In/Out
Out
In
Out
In
Out
In
MW(pin) = 1
CMS(cr1) = 1
CMS(cr1) = 0
CONF2(pin) = 1
MW(pin) = 0
MO(pin) = 1
CONF2(pin) = 0
CONF1(pin) = 1
CONF1(pin) = 0
MO(pin) = 0
STLC5412
9/74
相關PDF資料 |
PDF描述 |
|---|---|
| STLC5444 | Quad Feed Power Supply(ISDN四饋電電源) |
| STLC5460 | Line Card Interface Controller(線路卡片接口控制器) |
| STLC7546 | MODEM (V.34bis) Analog Front End(調制解調器模擬前端) |
| STLC7550TQFP | LOW POWER LOW VOLTAGE ANALOG FRONT END |
| STLC7550TQF7 | LOW POWER LOW VOLTAGE ANALOG FRONT END |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STLC54155 | 功能描述:電信集成電路 155MBit Coaxial Intr RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| STLC5432 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2Mbit CEPT & PRIMARY RATE CONTROLLER DEVICE |
| STLC5432Q | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2Mbit CEPT & PRIMARY RATE CONTROLLER DEVICE |
| STLC5444 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:QUAD FEEDER POWER SUPPLY |
| STLC5444B1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:QUAD FEEDER POWER SUPPLY |
發布緊急采購，3分鐘左右您將得到回復。