參數資料
型號： STLC5412
廠商： 意法半導體
英文描述： 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE
中文描述： 2B1Q U接口裝置加強與無繩模式
文件頁數： 44/74頁
文件大?。?/td> 655K
代理商： STLC5412
SFS = 0: SFSx is an input that synchronizes the
transmitsuperframe.
SFS = 1: SFSx is an
Transmit Superframe. In NT mode
SFSx is always an output.
NTS
LT / NT mode Select.
NTS = 0: LT mode selected
NTS = 1: NT mode selected
DMO
D channel Transfer mode Select.(
μ
W/DSI
only)
Significantonly when DEN=1.
output indicating the
DMO = 1: D channel data is shifted in and out on
Dx and Dr pins in continuous mode at
16 kbit/s on the falling and rising
edges of DCLK respectively.
DMO = 0: D channel data is shifted in and out on
Dx and Dr pins in a TDM mode at the
BCLK frequency on the falling and
rising edges of BCLK respectively
when the assigned time-slots are
active.
T24D:
24mstimer disable (GCIonly).
T24D = 1: The timer watches at theexchange on
MONITOR channeleverytime the UID
sends new byte. If it expires before
pre-acknoledgement,
message is generated; In this last
case, the abortedmessageis lost.
T24D = 0: The timer is desable. This means for
instance that UID may wait an pre-
acknoledgementfor ever.
DEN
D channelport Enable. (
μ
W/DSI only)
an
abort
DEN = 0: D channel port disabled. D bits are
transferred on Br and Bx; Multiplexed
modeis selectedautomatically.
DEN = 1: D channel port (DX, DR, and DCLK
when DMO bit equal 1) is selected. D
bits are transferred on Dr and Dx in a
modedepending on DMO bit setting.
CID
: C/I channeldisable(GCI only).
CID = 0:
TXACT and RXACT registers only
accessiblevia the C/I channel.
Others registers only accessible via
MONITOR channel.
All registers only accessible via the
MONITOR channel.
ETC
2B+D Data Extended Transparencychannel.
CID = 1:
ETC = 1: 2B+D
channel
transparency
soon as
is
is
enabled as
superframesynchronized.
the line
ETC = 0: 2B+D channel transparency is under
control of the on-chip state machine:
act bit equal one both directions.
BP1
Break Point 1 during activation(significative
only when NTS = 0: LT mode) .
BP1 = 1: During an activation attempt from the
loop, (before SL2 sending) UID waits
for
an
AR
activation. It is recommended to set
BP1 equal 1 forrepetor application.
BP1 = 0: The
activation
automatically processed without the
need of an ARcommand.
EIF
Error IndicationFilter.
Significant in NT mode only
command
to
pursue
procedure
is
EIF = 0:
act bit is set to zero in the transmit
superframe in case of EI command,
even if EI is sent sporadically.
act bit may be not set to zero in the
transmit superframe in case of EI
command with a duration of less than
36ms.
BP2
Break Point 2 during activation. Significant
only when NTS=0 (LT selected)
EIF = 1:
BP2 = 1: During a full activation procedure, UID
receiving
act bit set to one in the
received SN3 signal, UID waits for an
AI command to send act bit equal one
in SL3 signal. It is recommended to set
BP2 equal 1 for repetorapplication.
BP2 = 0: The activation procedure described
above
is
automatically
without the need of an AI command.
BFH9D
: Back from H9 disabled. (Significant in NT
mode only)
processed
BFH9D = 0: UID
is
in
H9
state
(pending
deactivation) after reception of dea
bit = 0. It is waiting a loss of signal to
return in H1 state via H12.
BFH9D = 1: UID
is
deactivation) after reception of dea
bit = 0. It is waiting a loss of signal to
return in H1 state via H12, or dea bit
= 1; In this last case UID returns in
the previous state.
RR
Repetormode.
H9
state
(pending
RR = 0:
UID
with the standard requirements for NT1
or LT equipment depending on NTS bit
select. See state matrix for the detailed
behaviourof UID.
activation/deactivation
complies
STLC5412
44/74
相關PDF資料
PDF描述
STLC5412FN 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE
STLC5412P 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE
STLC5444 Quad Feed Power Supply(ISDN四饋電電源)
STLC5460 Line Card Interface Controller(線路卡片接口控制器)
STLC7546 MODEM (V.34bis) Analog Front End(調制解調器模擬前端)
相關代理商/技術參數
參數描述
STLC5412FN 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE
STLC5412P 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE
STLC54155 功能描述:電信集成電路 155MBit Coaxial Intr RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray
STLC5432 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2Mbit CEPT & PRIMARY RATE CONTROLLER DEVICE
STLC5432Q 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2Mbit CEPT & PRIMARY RATE CONTROLLER DEVICE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*