- 您現在的位置：買賣IC網 > PDF目錄380765 > STLC5412 (意法半導體) 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE PDF資料下載
參數資料
| 型號： | STLC5412 |
| 廠商： | 意法半導體 |
| 英文描述： | 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE |
| 中文描述： | 2B1Q U接口裝置加強與無繩模式 |
| 文件頁數： | 35/74頁 |
| 文件大?。?/td> | 655K |
| 代理商： | STLC5412 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
TEST FUNCTIONS
Various test functions are provided for transmitted
pulse waveform checking, power spectral density
measurementand transmitterlinearity.
Three commands in TXACT register are provided.
The associatedtest function is enabledas long as
the command is not disabled by any other com-
mand.
SP1: (0010) Send Single Pulses+1, -1:
+1, -1, pulses are transmitted consecutively onto
the line, one pulse per frame.
SP3: (1011) Send Single Pulses+3, -3:
+3, -3, pulses are transmitted consecutively onto
the line, one pulse per frame.
RDT: (0011)Random Data Transmitted:
Random data can be transmitted onto the line
continuously.B1, B2 and D channeltransparency
between the digital interface and the line is en-
abled.
When auto-mode is selected, two test inputs
(TEST1, TEST2) are provided allowing the same
test functions as described above but without the
need of a microcontroller. See Table 6 for Test
pins biasing.
Table 6:
Test Pins
TEST1
1
1
0
0
TEST2
1
0
1
0
FUNCTIONS
Normal operation
Send Single Pulse
±
1
Random Data Transmitted
Send Single Pulse
±
3
TURNING ON AND OFF THE DEVICE
STLC5412 contains an automatic sequencer for
the complete control of the start-up activation se-
quences. Interactions with an external control unit
requires only Activate Request and Deactivate
Request commands, with the option of inserting
break-points in the sequence for additionalexter-
nal control allowing for instance easy building of a
repetor application. Automatic control of act,
uoa/sai and dea bitsin the M4 bit positionsis pro-
vided, along with the specified 40 ms, 480 ms and
15 s timers usedduring the sequencing.
Except the Power up and Power down control
that is slightly different, the Activation/Deactiva-
tion procedures are identical in GCI and Mi-
crowire/DSI modes. Same command codes or in-
dication codes are used. In Microwire and GCI
mode, activation control is done by writing in the
Activation Control Register TXACT and by read-
ing the Activation Indication Register RXACT. For
TXACT and RXACT access, MICROWIRE port is
used in MICROWIRE mode and C/I channel (or
MONITOR channel depending of CID bit in CR2
register) is used in GCI mode.
In MICROWIRE mode, a primitive indication gen-
erates first an interrupt requesting an action from
the Microprocessor, in GCI mode the primitive In-
dication is directly transmitted via C/I (or MONI-
TOR channel).
Power on initialization
Following
STLC5412 enters the power down deactivated
state in MICROWIRE mode or in GCI mode de-
pendingon the polarizationof the MW input.
All the internal circuits including the master oscil-
lator are inactive and in a low power state except
for the 10 kHz Tone signal detector. The line out-
puts LO+/LO- are low impedance and all digital
outputs are high impedance. All programmable
registers and the activation controller are reset to
their default value.
GCI configuration is defined by means of the con-
figuration pins M0, CONF1 and CONF2 when
Power supplyis turnedon.
For LT and NT1-2 equipments,GCI configuration
should be completed by means of Control Regis-
ter Programming. See Table 1 for configuration
pins bias.
the
initial
application
of
power,
Line signal detection
When UID is in the power down state and a
10kHz tone TN or TL is detected from the line
LSD and INT (MICROWIRE/DSI only) open drain
outputs are forced to zero.
In NT configuration , code LSD (0000) is loaded
in the activationindicationregister RXACT.
In LT configuration, code AP (1000) is loaded in
the activationindication registerRXACT.
In Microwire/DSI these indications are sent onto
CO at the following access even if the UID is still
in power down mode.
In GCI these indications are sent onto the C/I
channel as soon as GCI clocksare available.
LSD open drain output is set back in the high im-
pedancestateas soon as the UID is poweredup.
INT open drain output is set back in the high im-
pedancestatewhen CS input is detectedat zero.
Depending of the ACTAUT and PUPAUT bits in
CR6 register, UID can powered up itself, also
automaticallyto startthe activation.
For all auto mode configurations, on 10KHz tone
reception, power up and activation procedure are
full automatic, but in NT1 auto, UID waits the uoa
bit from the line before to provide (or not) the
cloks and primitives to the S device.
Power up control
Microwire/DSI: control instruction PUP in
ACT
STLC5412
35/74
相關PDF資料 |
PDF描述 |
|---|---|
| STLC5412FN | 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE |
| STLC5412P | 2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE |
| STLC5444 | Quad Feed Power Supply(ISDN四饋電電源) |
| STLC5460 | Line Card Interface Controller(線路卡片接口控制器) |
| STLC7546 | MODEM (V.34bis) Analog Front End(調制解調器模擬前端) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STLC5412FN | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE |
| STLC5412P | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2B1Q U INTERFACE DEVICE ENHANCED WITH DECT MODE |
| STLC54155 | 功能描述:電信集成電路 155MBit Coaxial Intr RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| STLC5432 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2Mbit CEPT & PRIMARY RATE CONTROLLER DEVICE |
| STLC5432Q | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2Mbit CEPT & PRIMARY RATE CONTROLLER DEVICE |
發布緊急采購，3分鐘左右您將得到回復。