- 您現在的位置：買賣IC網 > PDF目錄299945 > STK401-040 (Sanyo Electric Co.,Ltd.) AF Power Amplifier (Split Power Supply) (25 W + 25 W min, THD = 0.4%) PDF資料下載
參數資料
| 型號： | STK401-040 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | AF Power Amplifier (Split Power Supply) (25 W + 25 W min, THD = 0.4%) |
| 中文描述： | 自動對焦功率放大器（斯普利特電源）（25瓦25瓦分鐘，總諧波失真\u003d 0.4％） |
| 文件頁數： | 4/9頁 |
| 文件大小： | 464K |
| 代理商： | STK401-040 |
Description of External Circuits
No. 4341-4/9
STK401-020
C1, 11
For input coupling capacitor. Used for DC current blocking. When capacitor reactance with low frequency is increased, the reactance
value should be reduced in order to reduce the output noise from the signal resistance dependent 1/f noise. In response to the popping
noise which occurs when the system power is turned on, C1 and C11 which determine the decay time constant on the input side are
increased while C3 and C13 on the NF side are decreased.
C2, 12
For input filter capacitor. Permits high-region noise reduction by utilizing filter constructed with R1 and R11.
C3, 13
For NF capacitor. This capacitor determines the decline of the cut-off frequency and is calculated according to the following equation.
fL =
1
2
π X C3 (13) X R3 (13)
For the purpose of achieving voltage gains prior to reduction, it is best that C3 and C13 are large. However, because the shock
noise which occurs when the system power is turned on tends to increase, values larger than those absolutely necessary should be
avoided.
C5, 15
For oscillation prevention capacitor. A Mylar capacitor with temperature and frequency features is recommended.
C6, 7
For oscillation prevention capacitor. To ensure safe IC functioning, the capacitor should be installed as close as possible to the IC
power pin to reduce power impedance. An electrolytic capacitor is good.
C8, 9
For decoupling capacitor. Reduces shock noise during power up using decay time constant circuits with R8 and R9 and eliminates
components such as ripples crossing over into the input side from the power line.
R1, 11
For input filter applied resistor.
R2, 12
For input bias resistor. The input pin is biased to zero potential. Input impedance is mostly decided with this resistance value.
R3, 13, 4, 14
For resistors to determine voltage gain (VG). We recommend a VG = 40 dB using R3 and R13 = 560
and R4 and R14 = 56. VG
adjustments are best performed using R3 and R13. When using R4 and R14 for such purposes, R4 and R14 should be set to equal R2
and R12 in order to establish a stable VN balance.
R5, 15
For oscillation prevention resistor.
R6, 16
For oscillation prevention resistor. This resistor’s electrical output resides in the signal frequency and is calculated according to the
following formula.
P R6 (16) =
(
VCC max/√2
)
2 × R6 (16)
1/2
π fC5 (15) + R6 (16)
f = output signal frequency upper limit
R8, 9
For ripple filter applied resistor. PO max, ripple rejection and power-up shock noise are modified according to this value. Set the
electrical output of these resistors while keeping in mind the flow of peak current during recharging to C8 and C9 which function as pre-
drive TR control resistors during load shorts.
L1, 2
For oscillation prevention coil. Compensates phase dislocation caused by load capacitors and ensures stable oscillation.
相關PDF資料 |
PDF描述 |
|---|---|
| STK401-050 | AF Power Amplifier (Split Power Supply) (30 W + 30 W min, THD = 0.4%) |
| STK401-060 | 3ch AF Power Amplifier(Split Power Supply) 10W+10W+10W,THD=0.4% |
| STK401-070 | 2ch AF Power Amplifier (Split Power Supply) 40W + 40 W, THD = 0.08% |
| STK401-080 | AF Power Amplifier (Split Power Supply) (45 W + 45 W min, THD = 0.4%) |
| STK401-090 | Two-Channel AF Power Amplifier (+- Power Supply) 100 W + 100 W Minimum, THD = 0.4% |
相關代理商/技術參數 |
參數描述 |
|---|---|
| STK401-050 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:AF Power Amplifier (Split Power Supply) (50 W + 50 W min, THD = 0.4%) |
| STK401-060 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Features of the IMST Hybird ICs |
| STK401-070 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:AF Power Amplifier (Split Power Supply) (30 W + 30 W + 30 W min, THD = 0.4%) |
| STK401-080 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:2ch AF Power Amplifier (Split Power Supply) 30W + 30 W, THD = 0.08% |
| STK401-090 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Features of the IMST Hybird ICs |
發布緊急采購，3分鐘左右您將得到回復。