- 您現在的位置：買賣IC網 > PDF目錄299926 > SST26WF032-80-4I-QAE (SILICON STORAGE TECHNOLOGY INC) 32M X 1 SPI BUS SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | SST26WF032-80-4I-QAE |
| 廠商： | SILICON STORAGE TECHNOLOGY INC |
| 元件分類： | PROM |
| 英文描述： | 32M X 1 SPI BUS SERIAL EEPROM, PDSO8 |
| 封裝： | 6 X 5 MM, ROHS COMPLIANT, WSON-8 |
| 文件頁數： | 4/36頁 |
| 文件大小： | 1339K |
| 代理商： | SST26WF032-80-4I-QAE |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
2010 Silicon Storage Technology, Inc.
S71409-01-000
01/10
12
1.8V Serial Quad I/O (SQI) Flash Memory
SST26WF032
Advance Information
No Operation (NOP)
The No Operation command only cancels a Reset Enable command. NOP has no impact on any other
command.
WRDI
Write Disable
04H
0
80 MHz
RBPR12
Read Block Protec-
tion Register
72H
0
1 to m/4
WBPR10,12
Write Block Protec-
tion Register
42H
0
1 to m/4
Lock Down Block
Protection Register
8DH
0
T3.0
1409
1. One BUS cycle is two clock periods (command, access, or data).
2. Address bits above the most significant bit of each density can be VIL or VIH.
3. RST command only executed if RSTEN command is executed first. Any intervening command will disable Reset.
4. Device accepts eight-clock command in SPI mode, or two-clock command in SQI mode.
5. After a power cycle, Read, High-Speed Read, and JEDEC-ID Read instructions input and output cycles are SPI bus
protocol.
6. Burst length– n = 8 Bytes: Data(00H); n = 16 Bytes: Data(01H); n = 32 Bytes: Data(02H); n = 64 Bytes: Data(03H).
7. The Quad J-ID read wraps the three Quad J-ID Bytes of data until terminated by a low-to-high transition on CE#
8. Sector Addresses: Use AMS - A12, remaining address are don’t care, but must be set to VIL or VIH.
9. Blocks are 64 KByte, 32 KByte, or 8KByte, depending on location. Block Erase Address: AMS - A16 for 64 KByte; AMS -
A15 for 32 KByte; AMS - A13 for 8 KByte. Remaining addresses are don’t care, but must be set to VIL or VIH.
10. Requires a prior WREN command.
11. The Read-Status register is continuous with ongoing clock cycles until terminated by a low-to-high transition on CE#.
12. Data is written/read from MSB to LSB. MSB = 79 for SST26WF032.
Table 3: Device Operation Instructions for SST26WF032
Instruction
Description
Command
Cycle1
Address
Cycle(s)2
Dummy
Cycle(s)
Data
Cycle(s)
Maximum
Frequency
相關PDF資料 |
PDF描述 |
|---|---|
| SST48CF048-C1 | 24M X 16 FLASH 3.3V PROM CARD, 100 ns, XMA50 |
| SST49LF008C-33-4C-NHE | 1M X 8 FLASH 3V PROM, 11 ns, PQCC32 |
| SSU-131MAT | SLIDE SWITCH, SP3T, LATCHED, 0.3A, 4VDC, SURFACE MOUNT-RIGHT ANGLE |
| SSU-121ART | SLIDE SWITCH, SPDT, LATCHED, 0.3A, 4VDC, SURFACE MOUNT-RIGHT ANGLE |
| SSW-102-22-F-D-VS | 4 CONTACT(S), FEMALE, STRAIGHT TWO PART BOARD CONNECTOR, SURFACE MOUNT, SOCKET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SST26WF032-80-4I-QAE-T | 制造商:Microchip Technology Inc 功能描述:1.65 TO 1.95V 32MBIT SERIAL QUAD I/O FLASH - Tape and Reel |
| SST26WF032-80-4I-S2AE | 功能描述:閃存 1.65 to 1.95V 32Mbit Serial Quad I/O Flsh RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| SST26WF032-80-4I-S2AE-T | 制造商:Microchip Technology Inc 功能描述:1.65 TO 1.95V 32MBIT SERIAL QUAD I/O FLASH - Tape and Reel |
| SST270 | 功能描述:JFET 45V 2mA RoHS:否 制造商:ON Semiconductor 晶體管極性:N-Channel 漏極電流（Vgs=0 時的 Idss）:50 mA 漏源電壓 VDS:15 V 閘/源擊穿電壓: 漏極連續電流:50 mA 配置: 安裝風格: 封裝 / 箱體:SC-59 封裝:Reel |
| SST270-E3 | 功能描述:JFET 45V 2mA RoHS:否 制造商:ON Semiconductor 晶體管極性:N-Channel 漏極電流（Vgs=0 時的 Idss）:50 mA 漏源電壓 VDS:15 V 閘/源擊穿電壓: 漏極連續電流:50 mA 配置: 安裝風格: 封裝 / 箱體:SC-59 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。