參數資料
型號: SC16C850LIB
廠商: NXP Semiconductors N.V.
元件分類: 收發器
英文描述: 1.8 V single UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode parallel bus interface
封裝: SC16C850LIB<SOT313|<<<1<Always Pb-free,;SC16C850LIB<SOT313|<<<1<Always Pb-free,;SC16C850LIB<SOT313|<<<1<Always Pb-free,;SC16C850LIBS<SOT617-1 (HVQFN3
文件頁數: 18/55頁
文件大小: 1029K
代理商: SC16C850LIB
SC16C850L
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 5 — 1 February 2011
18 of 55
NXP Semiconductors
SC16C850L
1.8 V single UART with 128-byte FIFOs and IrDA encoder/decoder
6.11 Sleep mode
Sleep mode is an enhanced feature of the SC16C850L UART. It is enabled when EFR[4],
the enhanced functions bit, is set
and
when IER[4] bit is set.
6.11.1
Conditions to enter Sleep mode
Sleep mode is entered when:
Modem input pins are not toggling.
The serial data input line, RX, is idle for 4 character time (logic HIGH) and AFCR1[4]
is logic 0. When AFCR1[4] is logic 1 the device will go to sleep regardless of the state
of the RX pin (see
Section 7.21
for the description of AFCR1 bit 4).
The TX FIFO and TX shift register are empty.
There are no interrupts pending.
The RX FIFO is empty.
In Sleep mode, the UART clock and baud rate clock are stopped. Since most registers are
clocked using these clocks, the power consumption is greatly reduced.
Remark:
Writing to the divisor latches, DLL and DLM, to set the baud clock, must not be
done during Sleep mode. Therefore, it is advisable to disable Sleep mode using IER[4]
before writing to DLL or DLM.
6.11.2
Conditions to resume normal operation
SC16C850L resumes normal operation by any of the following:
Receives a start bit on RX pin.
Data is loaded into transmit FIFO.
A change of state on any of the modem input pins
If the device is awakened by one of the conditions described above, it will return to the
Sleep mode automatically after all the conditions described in
Section 6.11.1
are met. The
device will stay in Sleep mode until it is disabled by setting any channel’s IER bit 4 to a
logic 0.
When the SC16C850L is in Sleep mode and the host data bus (D[7:0], A[2:0], IOW, IOR,
CS) remains in steady state, either HIGH or LOW, the Sleep mode supply current will be
in the
A range as specified in
Table 36 “Static characteristics”
. If any of these signals is
toggling or floating then the sleep current will be higher.
6.12 Low power feature
A Low power feature is provided by the SC16C850L to prevent the switching of the host
data bus from influencing the sleep current. When the pin LOWPWR is activated (logic
HIGH), the device immediately and unconditionally goes into Low power mode. All clocks
are stopped and most host interface pins are isolated to reduce power consumption. The
device only returns to normal mode when the LOWPWR pin is de-asserted. The pin can
be left unconnected because it has an internal pull-down resistor.
相關PDF資料
PDF描述
SC16C850LIBS 1.8 V single UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode parallel bus interface
SC16C850LIET 1.8 V single UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode parallel bus interface
SC16C850SVIBS 1.8 V single UART, 20 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface
SC16C850VIBS 1.8 V single UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and XScale VLIO bus interface
SC16C852LIB 1.8 V dual UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA) and 16 mode or 68 mode bus interface
相關代理商/技術參數
參數描述
SC16C850LIB,128 制造商:NXP Semiconductors 功能描述:
SC16C850LIB,151 制造商:NXP Semiconductors 功能描述:
SC16C850LIB,157 制造商:NXP Semiconductors 功能描述:
SC16C850LIBS 功能描述:UART 接口集成電路 1.8V 1 CH UART 128B FIFO 5MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850LIBS,115 功能描述:UART 接口集成電路 1.8V 1 CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel