- 您現在的位置：買賣IC網 > PDF目錄379352 > SC16C752BIB48 (NXP Semiconductors N.V.) 5 V, 2.2 V and 2.5 V dual UART, 5 Mbit-s (max.), with 64-byte FIFOs PDF資料下載
參數資料
| 型號： | SC16C752BIB48 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 收發器 |
| 英文描述： | 5 V, 2.2 V and 2.5 V dual UART, 5 Mbit-s (max.), with 64-byte FIFOs |
| 封裝： | SC16C752BIB48<SOT313-2 (LQFP48)|<<http://www.nxp.com/packages/SOT313-2.html<1<Always Pb-free,;SC16C752BIB48<SOT313-2 (LQFP48)|<<http://www.nxp.com/packages/SOT313-2.html& |
| 文件頁數： | 6/47頁 |
| 文件大?。?/td> | 945K |
| 代理商： | SC16C752BIB48 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
SC16C752B
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 6 — 30 November 2010
6 of 47
NXP Semiconductors
SC16C752B
5 V, 2.2 V and 2.5 V dual UART, 5 Mbit/s (max.), with 64-byte FIFOs
IOW
15
12
I
Input/Output Write strobe (active LOW).
A LOW-to-HIGH transition on IOW
will transfer the contents of the data bus (D0 to D7) from the external CPU to an
internal register that is defined by address bits A0 to A2 and CSA and CSB.
not connected
n.c.
12, 24,
25, 37
32
9
-
-
OPA
OPB
22
7
O
O
User defined outputs.
This function is associated with individual channels A
and B. The state of these pins is defined by the user through the software
settings of MCR[3]. INTA-INTB are set to active mode and OPA-OPB to a logic 0
when MCR[3] is set to a logic 1. INTA-INTB are set to the 3-state mode and
OPA-OPB to a logic 1 when MCR[3] is set to a logic 0. The output of these two
pins is HIGH after reset.
Reset.
This pin will reset the internal registers and all the outputs. The UART
transmitter output and the receiver input will be disabled during reset time.
RESET is an active HIGH input.
Ring Indicator (active LOW).
These inputs are associated with individual
UART channels, A and B. A logic 0 on these pins indicates the modem has
received a ringing signal from the telephone line. A LOW-to-HIGH transition on
these input pins generates a modem status interrupt, if enabled. The state of
these inputs is reflected in the Modem Status Register (MSR).
Request to Send (active LOW).
These outputs are associated with individual
UART channels, A and B. A logic 0 on the RTSn pin indicates the transmitter
has data ready and waiting to send. Writing a logic 1 in the modem control
register MCR[1] will set this pin to a logic 0, indicating data is available. After a
reset these pins are set to a logic 1. These pins only affect the transmit and
receive operations when auto-RTS function is enabled via the Enhanced
Feature Register (EFR[6]) for hardware flow control operation.
Receive data input.
These inputs are associated with individual serial channel
data to the SC16C752B. During the local Loopback mode, these RXn input pins
are disabled and transmit data is connected to the UART receive input internally.
Receive Ready (active LOW).
RXRDYA or RXRDYB goes LOW when the
trigger level has been reached or the FIFO has at least one character. It goes
HIGH when the receive FIFO is empty.
Transmit data A, B.
These outputs are associated with individual serial transmit
channel data from the SC16C752B. During the local Loopback mode, the TXn
output pin is disabled and transmit data is internally connected to the UART
receive input.
Transmit Ready (active LOW).
TXRDYA or TXRDYB go LOW when there are
at least a trigger level number of spaces available or when the FIFO is empty. It
goes HIGH when the FIFO is full or not empty.
Power supply input
Crystal or external clock input.
Functions as a crystal input or as an external
clock input. A crystal can be connected between XTAL1 and XTAL2 to form an
internal oscillator circuit (see
Figure 13
). Alternatively, an external clock can be
connected to this pin to provide custom data rates.
Output of the crystal oscillator or buffered clock.
(See also XTAL1.) XTAL2
is used as a crystal oscillator output or a buffered clock output.
RESET
36
24
I
RIA
RIB
41
21
-
-
I
I
RTSA
RTSB
33
22
23
15
O
O
RXA
RXB
5
4
4
3
I
I
RXRDYA
RXRDYB
31
18
-
-
O
O
TXA
TXB
7
8
5
6
O
O
TXRDYA
TXRDYB
43
6
-
-
O
O
V
CC
XTAL1
42
13
26
10
I
I
XTAL2
14
11
O
Table 2.
Symbol
Pin description
…continued
Pin
LQFP48 HVQFN32
Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C752BIBS | 5 V, 2.2 V and 2.5 V dual UART, 5 Mbit-s (max.), with 64-byte FIFOs |
| SC16C754BIA68 | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.) with 64-byte FIFOs |
| SC16C754BIB80 | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.) with 64-byte FIFOs |
| SC16C754BIBM | 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit-s (max.) with 64-byte FIFOs |
| SC16C850IBS | 2.5 V to 3.3 V UART, 5 Mbit-s (max.) with 128-byte FIFOs, infrared (IrDA), and 16 mode or 68 mode parallel bus interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C752BIB48,128 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C752BIB48,151 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C752BIB48,157 | 功能描述:UART 接口集成電路 2CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C752BIB48151 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| SC16C752BIB48-F | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。