- 您現在的位置：買賣IC網 > PDF目錄379352 > SC16C2552BIA44 (NXP Semiconductors N.V.) 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit-s (max.), with 16-byte FIFOs PDF資料下載
參數資料
| 型號： | SC16C2552BIA44 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 收發器 |
| 英文描述： | 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit-s (max.), with 16-byte FIFOs |
| 封裝： | SC16C2552BIA44<SOT187-2 (PLCC44)|<<http://www.nxp.com/packages/SOT187-2.html<1<week 49, 2004,;SC16C2552BIA44<SOT187-2 (PLCC44)|<<http://www.nxp.com/packages/SOT187-2.html |
| 文件頁數： | 7/38頁 |
| 文件大小： | 179K |
| 代理商： | SC16C2552BIA44 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
SC16C2552B_3
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 12 February 2009
7 of 38
NXP Semiconductors
SC16C2552B
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
6.2 Internal registers
The SC16C2552B provides two sets of internal registers (A and B) consisting of
13 registers each for monitoring and controlling the functions of each channel of the
UART. These registers are shown in
Table 4
. The UART registers function as data holding
registers (THR/RHR), interrupt status and control registers (IER/ISR), a FIFO control
register (FCR), line status and control registers (LCR/LSR), modem status and control
registers (MCR/MSR), programmable data rate (clock) control registers (DLL/DLM), a
user accessible scratchpad register (SPR), and an Alternate Function Register (AFR).
[1]
The baud rate register and AFR register sets are accessible only when CS is a logic 0 and LCR[7] is a
logic 1 for the register set (A/B) being accessed.
6.3 FIFO operation
The 16 byte transmit and receive data FIFOs are enabled by the FIFO Control Register
(FCR) bit 0. The user can set the receive trigger level via FCR[7:6], but not the transmit
trigger level. The receiver FIFO section includes a time-out function to ensure data is
delivered to the external CPU. A time-out interrupt is generated whenever the Receive
Holding Register (RHR) has not been read following the loading of a character, or the
receive trigger interrupt is generated when RX FIFO level is equal to the program RX
trigger value.
6.4 Time-out interrupts
The interrupts are enabled by IER[3:0]. Care must be taken when handling these
interrupts. Following a reset, if the transmitter interrupt is enabled, the SC16C2552B will
issue an interrupt to indicate that the Transmit Holding Register is empty. The ISR register
provides the current singular highest priority interrupt only. A condition can exist where a
higher priority interrupt may mask the lower priority interrupt(s). Only after servicing the
higher pending interrupt will the lower priority interrupt(s) be reflected in the status
register. Servicing the interrupt without investigating further interrupt conditions can result
in data errors.
Table 4.
A2
General register set (THR/RHR, IER/ISR, MCR/MSR, FCR, LCR/LSR, SPR)
0
0
0
Receive Holding Register
0
0
1
Interrupt Enable Register
0
1
0
Interrupt Status Register
0
1
1
Line Control Register
1
0
0
Modem Control Register
1
0
1
Line Status Register
1
1
0
Modem Status Register
1
1
1
Scratchpad Register
Baud rate register set (DLL/DLM, AFR)
[1]
0
0
0
LSB of Divisor Latch
0
0
1
MSB of Divisor Latch
0
1
0
Alternate Function Register
Internal registers decoding
A0
Read mode
A1
Write mode
Transmit Holding Register
Interrupt Enable Register
FIFO Control Register
Line Control Register
Modem Control Register
n/a
n/a
Scratchpad Register
LSB of Divisor Latch
MSB of Divisor Latch
Alternate Function Register
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C550BIA44 | 5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs |
| SC16C550BIB48 | 5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs |
| SC16C550BIBS | 5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs |
| SC16C650BIB48 | 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder-decoder |
| SC16C650BIBS | 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder-decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C2552BIA44,512 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2552BIA44,518 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2552BIA44,529 | 功能描述:UART 接口集成電路 2CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2552BIA44512 | 制造商:NXP Semiconductors 功能描述:IC DUAL UART FIFO 5MBPS 5.5V LCC-44 |
| SC16C2552BIA44-T | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。