- 您現在的位置：買賣IC網 > PDF目錄379352 > SC16C2552BIA44 (NXP Semiconductors N.V.) 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit-s (max.), with 16-byte FIFOs PDF資料下載
參數資料
| 型號： | SC16C2552BIA44 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 收發器 |
| 英文描述： | 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit-s (max.), with 16-byte FIFOs |
| 封裝： | SC16C2552BIA44<SOT187-2 (PLCC44)|<<http://www.nxp.com/packages/SOT187-2.html<1<week 49, 2004,;SC16C2552BIA44<SOT187-2 (PLCC44)|<<http://www.nxp.com/packages/SOT187-2.html |
| 文件頁數： | 14/38頁 |
| 文件大?。?/td> | 179K |
| 代理商： | SC16C2552BIA44 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
SC16C2552B_3
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 03 — 12 February 2009
14 of 38
NXP Semiconductors
SC16C2552B
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
7.3 FIFO Control Register (FCR)
This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO trigger
levels and select the DMA mode.
7.3.1
DMA mode
7.3.1.1
Mode 0 (FCR bit 3 = 0)
Set and enable the interrupt for each single transmit or receive operation and is similar to
the 16C450 mode. Transmit Ready (TXRDY) will go to a logic 0 whenever an empty
transmit space is available in the Transmit Holding Register (THR). Receive Ready
(RXRDY) at the MFn pin will go to a logic 0 whenever the Receive Holding Register (RHR)
is loaded with a character and AFR[2:1] is set to the RXRDY mode.
7.3.1.2
Mode 1 (FCR bit 3 = 1)
Set and enable the interrupt in a block mode operation. The transmit interrupt is set when
the transmit FIFO has at least one empty location. TXRDY remains a logic 0 as long as
one empty FIFO location is available. The receive interrupt is set when the receive FIFO
fills to the programmed trigger level. However, the FIFO continues to fill regardless of the
programmed level until the FIFO is full. RXRDY at the MFn pin remains a logic 0 as long
as the FIFO fill level is above the programmed trigger level, and AFR[2:1] is set to the
RXRDY mode.
7.3.2
FIFO mode
Table 8.
Bit
7:6
FIFO Control Register bits description
Symbol
Description
FCR[7:6]
RCVR trigger. These bits are used to set the trigger level for the receive
FIFO interrupt.
An interrupt is generated when the number of characters in the FIFO
equals the programmed trigger level. However, the FIFO will continue to
be loaded until it is full. Refer to
Table 9
.
FCR[5:4]
Not used; initialized to logic 0.
FCR[3]
DMA mode select.
logic 0 = set DMA mode ‘0’ (normal default condition)
logic 1 = set DMA mode ‘1’
Transmit operation in mode ‘0’:
When the SC16C2552B is in the
16C450 mode (FIFOs disabled; FCR[0] = logic 0) or in the FIFO mode
(FIFOs enabled; FCR[0] = logic 1; FCR[3] = logic 0), and when there
are no characters in the transmit FIFO or Transmit Holding Register, the
TXRDYn pin will be a logic 0. Once active, the TXRDYn pin will go to a
logic 1 after the first character is loaded into the Transmit Holding
Register.
Receive operation in mode ‘0’:
When the SC16C2552B is in 16C450
mode, or in the FIFO mode (FCR[0] = logic 1; FCR[3] = logic 0) and
there is at least one character in the receive FIFO, the RXRDY signal at
the MFn pin will be a logic 0. Once active, the RXRDY signal at the
MFn pin will go to a logic 1 when there are no more characters in the
receiver. Note that the AFR register must be set to the RXRDY mode
prior to any possible reading of the RXRDY signal.
5:4
3
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C550BIA44 | 5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs |
| SC16C550BIB48 | 5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs |
| SC16C550BIBS | 5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs |
| SC16C650BIB48 | 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder-decoder |
| SC16C650BIBS | 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder-decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C2552BIA44,512 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2552BIA44,518 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2552BIA44,529 | 功能描述:UART 接口集成電路 2CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2552BIA44512 | 制造商:NXP Semiconductors 功能描述:IC DUAL UART FIFO 5MBPS 5.5V LCC-44 |
| SC16C2552BIA44-T | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。