參數資料
型號： S29GL032N90BFI32
廠商： SPANSION LLC
元件分類： PROM
英文描述： 2M X 16 FLASH 3V PROM, 90 ns, PBGA48
封裝： 8.15 X 6.15 MM, LEAD FREE, FBGA-48
文件頁數： 30/81頁
文件大?。?/td> 3095K
代理商： S29GL032N90BFI32
36
S29GL-N MirrorBit Flash Family
S29GL-N_01_12 October 29, 2008
Da ta
Sh e e t
8.15.1
Customer Lockable: Secured Silicon Sector NOT Programmed or Protected
At the Factory
Unless otherwise specified, the device is shipped such that the customer may program and protect the 256-
byte Secured Silicon sector.
The system may program the Secured Silicon Sector using the write-buffer, accelerated and/or unlock
bypass methods, in addition to the standard programming command sequence. See Command Definitions
Programming and protecting the Secured Silicon Sector must be used with caution since, once protected,
there is no procedure available for unprotecting the Secured Silicon Sector area and none of the bits in the
Secured Silicon Sector memory space can be modified in any way.
The Secured Silicon Sector area can be protected using one of the following procedures:
Write the three-cycle Enter Secured Silicon Sector Region command.
To verify the protect/unprotect status of the Secured Silicon Sector, follow the algorithm.
Once the Secured Silicon Sector is programmed, locked and verified, the system must write the Exit Secured
Silicon Sector Region command sequence to return to reading and writing within the remainder of the array.
8.15.2
Factory Locked: Secured Silicon Sector Programmed and Protected At the
Factory
In devices with an ESN, the Secured Silicon Sector is protected when the device is shipped from the factory.
The Secured Silicon Sector cannot be modified in any way. An ESN Factory Locked device has an 16-byte
random ESN at addresses 000000h–000007h. Please contact your sales representative for details on
ordering ESN Factory Locked devices.
Customers may opt to have their code programmed by the factory through the ExpressFlash service (Express
Flash Factory Locked). The devices are then shipped from the factory with the Secured Silicon Sector
permanently locked. Contact your sales representative for details on using the ExpressFlash service.
8.16
Write Protect (WP#/ACC)
The Write Protect function provides a hardware method of protecting the first or last sector without using VID.
Write Protect is one of two functions provided by the WP#/ACC input.
If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the first or
last sector independently of whether those sectors were protected or unprotected. Note that if WP#/ACC is at
VIL when the device is in the standby mode, the maximum input load current is increased. See the table in DC
If the system asserts VIH on the WP#/ACC pin, the device reverts to whether the first or last sector was
previously set to be protected or unprotected using the method described in Advanced Sector
Protection on page 30. Note that WP#/ACC contains an internal pull-up; when unconnected, WP#/ACC
is at VIH.
8.17
Hardware Data Protection
The command sequence requirement of unlock cycles for programming or erasing provides data protection
against inadvertent writes (refer to Table 10.1 on page 51 and Table 10.3 on page 53 for command
definitions). In addition, the following hardware data protection measures prevent accidental erasure or
programming, which might otherwise be caused by spurious system level signals during VCC power-up and
power-down transitions, or from system noise.
8.17.1
Low VCC Write Inhibit
When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC
power-up and power-down. The command register and all internal program/erase circuits are disabled, and
the device resets to the read mode. Subsequent writes are ignored until VCC is greater than VLKO. The
system must provide the proper signals to the control pins to prevent unintentional writes when VCC is greater
than VLKO.
相關PDF資料
PDF描述
S2A SURFACE MOUNT RECTIFIER
S2B SURFACE MOUNT RECTIFIER
S2C1R-1-5-H 4000 MHz - 8000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 1.7 dB INSERTION LOSS
S2D SURFACE MOUNT RECTIFIER
S2G SURFACE MOUNT RECTIFIER
相關代理商/技術參數
參數描述
S29GL032N90DFI020 功能描述:IC FLASH 32MBIT 90NS 64BGA 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:32Mb （4M x 8，2M x 16） 寫周期時間 - 字，頁:90ns 訪問時間:90ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:64-LBGA 供應商器件封裝:64 球加強型 BGA（9x9） 標準包裝:260
S29GL032N90DFI023 功能描述:IC FLASH 32MBIT 90NS 64BGA 制造商:cypress semiconductor corp 系列:GL-N 包裝:剪切帶（CT） 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:32Mb （4M x 8，2M x 16） 寫周期時間 - 字，頁:90ns 訪問時間:90ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:64-LBGA 供應商器件封裝:64 球加強型 BGA（9x9） 標準包裝:1
S29GL032N90FAI030 制造商:Spansion 功能描述:IC, FLASH - Trays
S29GL032N90FAI040 功能描述:閃存 32Mb 3V 90ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29GL032N90FFI010 功能描述:閃存 32Mb 3V 90ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*