參數資料
型號： S29GL032N90BFI32
廠商： SPANSION LLC
元件分類： PROM
英文描述： 2M X 16 FLASH 3V PROM, 90 ns, PBGA48
封裝： 8.15 X 6.15 MM, LEAD FREE, FBGA-48
文件頁數： 28/81頁
文件大小： 3095K
代理商： S29GL032N90BFI32
34
S29GL-N MirrorBit Flash Family
S29GL-N_01_12 October 29, 2008
Da ta
Sh e e t
8.12
Password Sector Protection
The Password Sector Protection method allows an even higher level of security than the Persistent Sector
Protection method. There are two main differences between the Persistent Sector Protection and the
Password Sector Protection methods:
When the device is first powered on, or comes out of a reset cycle, the PPB Lock Bit is set to the locked
state, or the freeze state, rather than cleared to the unlocked state, or the unfreeze state.
The only means to clear and unfreeze the PPB Lock Bit is by writing a unique 64-bit Password to the
device.
The Password Sector Protection method is otherwise identical to the Persistent Sector Protection method.
A 64-bit password is the only additional tool utilized in this method.
The password is stored in a one-time programmable (OTP) region outside of the flash memory. Once the
Password Protection Mode Lock Bit is set, the password is permanently set with no means to read, program,
or erase it. The password is used to clear and unfreeze the PPB Lock Bit. The Password Unlock command
must be written to the flash, along with a password. The flash device internally compares the given password
with the pre-programmed password. If they match, the PPB Lock Bit is cleared to the unfreezed state, and the
PPB bits can be altered. If they do not match, the flash device does nothing. There is a built-in 2 s delay for
each password check after the valid 64-bit password is entered for the PPB Lock Bit to be cleared to the
“unfreezed state”. This delay is intended to thwart any efforts to run a program that tries all possible
combinations in order to crack the password.
8.13
Password and Password Protection Mode Lock Bit
In order to select the Password Sector Protection method, the user must first program the password.
Spansion recommends that the password be somehow correlated to the unique Electronic Serial Number
(ESN) of the particular flash device. Each ESN is different for every flash device; therefore each password
should be different for every flash device. While programming in the password region, the customer may
perform Password Read operations. Once the desired password is programmed in, the customer must then
set the Password Protection Mode Lock Bit. This operation achieves two objectives:
1. It permanently sets the device to operate using the Password Protection Mode. It is not possible to
reverse this function.
2. It also disables all further commands to the password region. All program, and read operations are
ignored.
Both of these objectives are important, and if not carefully considered, may lead to unrecoverable errors. The
user must be sure that the Password Sector Protection method is desired when programming the Password
Protection Mode Lock Bit. More importantly, the user must be sure that the password is correct when the
Password Protection Mode Lock Bit is programmed. Due to the fact that read operations are disabled, there is
no means to read what the password is afterwards. If the password is lost after programming the Password
Protection Mode Lock Bit, there is no way to clear and unfreeze the PPB Lock Bit. The Password Protection
Mode Lock Bit, once programmed, prevents reading the 64-bit password on the DQ bus and further password
programming. The Password Protection Mode Lock Bit is not erasable. Once Password Protection Mode
Lock Bit is programmed, the Persistent Protection Mode Lock Bit is disabled from programming, guaranteeing
that no changes to the protection scheme are allowed.
8.13.1
64-bit Password
The 64-bit Password is located in its own memory space and is accessible through the use of the Password
Program and Password Read commands. The password function works in conjunction with the Password
Protection Mode Lock Bit, which when programmed, prevents the Password Read command from reading
the contents of the password on the pins of the device.
相關PDF資料
PDF描述
S2A SURFACE MOUNT RECTIFIER
S2B SURFACE MOUNT RECTIFIER
S2C1R-1-5-H 4000 MHz - 8000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 1.7 dB INSERTION LOSS
S2D SURFACE MOUNT RECTIFIER
S2G SURFACE MOUNT RECTIFIER
相關代理商/技術參數
參數描述
S29GL032N90DFI020 功能描述:IC FLASH 32MBIT 90NS 64BGA 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:32Mb （4M x 8，2M x 16） 寫周期時間 - 字，頁:90ns 訪問時間:90ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:64-LBGA 供應商器件封裝:64 球加強型 BGA（9x9） 標準包裝:260
S29GL032N90DFI023 功能描述:IC FLASH 32MBIT 90NS 64BGA 制造商:cypress semiconductor corp 系列:GL-N 包裝:剪切帶（CT） 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:32Mb （4M x 8，2M x 16） 寫周期時間 - 字，頁:90ns 訪問時間:90ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:64-LBGA 供應商器件封裝:64 球加強型 BGA（9x9） 標準包裝:1
S29GL032N90FAI030 制造商:Spansion 功能描述:IC, FLASH - Trays
S29GL032N90FAI040 功能描述:閃存 32Mb 3V 90ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
S29GL032N90FFI010 功能描述:閃存 32Mb 3V 90ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*