- 您現在的位置：買賣IC網 > PDF目錄299877 > S29GL032N90BFI32 (SPANSION LLC) 2M X 16 FLASH 3V PROM, 90 ns, PBGA48 PDF資料下載
參數資料
| 型號： | S29GL032N90BFI32 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 90 ns, PBGA48 |
| 封裝： | 8.15 X 6.15 MM, LEAD FREE, FBGA-48 |
| 文件頁數： | 26/81頁 |
| 文件大?。?/td> | 3095K |
| 代理商： | S29GL032N90BFI32 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
32
S29GL-N MirrorBit Flash Family
S29GL-N_01_12 October 29, 2008
Da ta
Sh e e t
Volatile. Individual PPB bits are set with a program command but must all be cleared as a group through an
erase command.
The PPB Lock Bit adds an additional level of protection. Once all PPB bits are programmed to the desired
settings, the PPB Lock Bit may be set to the “freeze state”. Setting the PPB Lock Bit to the “freeze state”
disables all program and erase commands to the Non-Volatile PPB bits. In effect, the PPB Lock Bit locks the
PPB bits into their current state. The only way to clear the PPB Lock Bit to the “unfreeze state” is to go
through a power cycle, or hardware reset. The Software Reset command does not clear the PPB Lock Bit to
the “unfreeze state”. System boot code can determine if any changes to the PPB bits are needed e.g. to allow
new system code to be downloaded. If no changes are needed then the boot code can set the PPB Lock Bit
to disable any further changes to the PPB bits during system operation.
The WP# write protect pin adds a final level of hardware protection. When this pin is low it is not possible to
change the contents of the WP# protected sectors. These sectors generally hold system boot code. So, the
WP# pin can prevent any changes to the boot code that could override the choices made while setting up
sector protection during system initialization.
It is possible to have sectors that have been persistently locked, and sectors that are left in the dynamic state.
The sectors in the dynamic state are all unprotected. If there is a need to protect some of them, a simple DYB
Set command sequence is all that is necessary. The DYB Set and DYB Clear commands for the dynamic
sectors switch the DYB bits to signify protected and unprotected, respectively. If there is a need to change the
status of the persistently locked sectors, a few more steps are required. First, the PPB Lock Bit must be
disabled to the “unfreeze state” by either putting the device through a power-cycle, or hardware reset. The
PPB bits can then be changed to reflect the desired settings. Setting the PPB Lock Bit once again to the
“freeze state” locks the PPB bits, and the device operates normally again.
To achieve the best protection, execute the PPB Lock Bit Set command early in the boot code, and protect
the boot code by holding WP# = VIL.
8.11.2
Persistent Protection Bit (PPB)
A single Persistent (non-volatile) Protection Bit is assigned to each sector. If a PPB is programmed to the
protected state through the “PPB Program” command, that sector is protected from program or erase
operations and is therefor read-only. If a PPB requires erasure, all of the sector PPB bits must first be erased
in parallel through the “All PPB Erase” command. The “All PPB Erase” command preprograms all PPB bits
prior to PPB erasing. All PPB bits erase in parallel, unlike programming where individual PPB bits are
programmable. The PPB bits are limited to the same number of cycles as a flash memory sector.
Programming the PPB bit requires the typical word programming time without utilizing the Write Buffer.
During a PPB bit programming and all PPB bit erasing sequence executions, the DQ6 Toggle Bit I toggles
until the programming of the PPB bit or erasing of all PPB bits has completed to indicate programming and
erasing status. Erasing all of the PPB bits at once requires typical sector erase time. During the erasing of all
PPB bits, the DQ3 Sector Erase Timer bit outputs a 1 to indicate the erasure of all PPB bits are in progress.
When the erasure of all PPB bits has completed, the DQ3 Sector Erase Timer bit outputs a 0 to indicate that
all PPB bits have been erased. Reading the PPB Status bit requires the initial access time of the device.
相關PDF資料 |
PDF描述 |
|---|---|
| S2A | SURFACE MOUNT RECTIFIER |
| S2B | SURFACE MOUNT RECTIFIER |
| S2C1R-1-5-H | 4000 MHz - 8000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 1.7 dB INSERTION LOSS |
| S2D | SURFACE MOUNT RECTIFIER |
| S2G | SURFACE MOUNT RECTIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29GL032N90DFI020 | 功能描述:IC FLASH 32MBIT 90NS 64BGA 制造商:cypress semiconductor corp 系列:GL-N 包裝:托盤 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:32Mb （4M x 8，2M x 16） 寫周期時間 - 字，頁:90ns 訪問時間:90ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:64-LBGA 供應商器件封裝:64 球加強型 BGA（9x9） 標準包裝:260 |
| S29GL032N90DFI023 | 功能描述:IC FLASH 32MBIT 90NS 64BGA 制造商:cypress semiconductor corp 系列:GL-N 包裝:剪切帶（CT） 零件狀態:在售 存儲器類型:非易失 存儲器格式:閃存 技術:FLASH - NOR 存儲容量:32Mb （4M x 8，2M x 16） 寫周期時間 - 字，頁:90ns 訪問時間:90ns 存儲器接口:并聯 電壓 - 電源:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:64-LBGA 供應商器件封裝:64 球加強型 BGA（9x9） 標準包裝:1 |
| S29GL032N90FAI030 | 制造商:Spansion 功能描述:IC, FLASH - Trays |
| S29GL032N90FAI040 | 功能描述:閃存 32Mb 3V 90ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29GL032N90FFI010 | 功能描述:閃存 32Mb 3V 90ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。